Home › Engine / Hybrid System › 2KD-FTV STARTING › STARTER(for DENSO Made)
RM1840EF _51 Engine / Hybrid System _009604 2KD-FTV STARTING _0052423 STARTER(for DENSO Made) A

2KD-FTV STARTING  STARTER(for DENSO Made)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE STARTER YOKE ASSEMBLY

A074096

a.

Remove the nut and disconnect the lead wire from terminal C.


b.

Remove the 2 through bolts.


c.

Pull out the starter yoke together with the armature.


d.

Remove the O-ring from the starter yoke.


Hide 2.REMOVE STARTER CLUTCH SUB-ASSEMBLY

a.
A289336

Remove the 2 screws and magnet starter switch assembly.


b.

Remove the return spring.


c.
A253088
2.75,0.802 2.75,0.469 2.75,0.469 2.948,0.469 false 1.479,0.76 1.479,0.406 1.479,0.406 1.292,0.406 false 1.198,1.26 1.198,0.823 1.198,0.823 0.958,0.823 false 0.781,1.469 0.781,1.219 0.781,1.219 0.625,1.219 false 0.365,1.604 0.365,1.458 0.365,1.458 0.271,1.458 false 0.406,2.542 0.406,2.75 0.406,2.75 0.531,2.75 false 1.448,2.49 1.448,2.708 1.448,2.708 1.573,2.708 false 1.125,0.313 1.344,0.51 0.219,0.198 10 *1 0.781,0.729 1.01,0.917 0.229,0.188 10 *2 0.448,1.115 0.677,1.281 0.229,0.167 10 *3 0.104,1.354 0.292,1.542 0.188,0.188 10 *4 0.552,2.635 0.76,2.813 0.208,0.177 10 *5 1.615,2.604 1.823,2.771 0.208,0.167 10 *6 2.99,0.375 3.208,0.563 0.219,0.188 10 *7
*1 Pinion Gear
*2 Idler Gear
*3 Retainer
*4 Clutch Roller
*5 Return Spring
*6 Starter Clutch Assembly
*7 Stater Drive Housing


Remove the pinion gear, idler gear, clutch roller, retainer and starter clutch assembly from the starter drive housing.


d.
A115020
2.688,0.417 2.573,0.417 2.573,0.417 2.146,0.74 false 2.76,0.323 3.031,0.521 0.271,0.198 10 *1
*1 Magnet Hand


Using a magnet hand, remove the steel ball from the clutch shaft hole.


Hide 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A115021

Remove the 2 screws and commutator end frame from the starter yoke.


b.

Remove the O-ring from the starter yoke.


c.

Disconnect the 4 starter yoke brushes from the starter brush holder.

i.
A115022

Using a screwdriver, pull back the spring.


ii.

Disconnect the brush from the starter brush holder.



d.

Remove the starter brush holder from the starter yoke.


Hide 4.REMOVE STARTER ARMATURE ASSEMBLY

a.

Remove the starter armature from the starter yoke.