Home › Engine / Hybrid System › 2KD-FTV STARTING › PRE-HEATING SYSTEM(w/o DPF)
RM1840EF _51 Engine / Hybrid System _009604 2KD-FTV STARTING _0052425 PRE-HEATING SYSTEM(w/o DPF) G

2KD-FTV STARTING  PRE-HEATING SYSTEM(w/o DPF)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT ILLUMINATION DURATION OF GLOW INDICATOR LIGHT

a.

Inspect the light illumination duration.

A113413
3.573,2.417 3.854,2.594 0.281,0.177 10 *b 1.813,1.229 2.042,1.417 0.229,0.188 10 *a 2.292,1.021 2.531,1.198 0.24,0.177 10 6.5 2.333,0.531 2.531,0.698 0.198,0.167 10 10 2.292,1.406 2.521,1.583 0.229,0.177 10 3.5 2.573,2.208 2.854,2.375 0.281,0.167 10 -9.4 2.969,2.208 3.24,2.375 0.271,0.167 10 -8.5 2.292,1.865 2.521,2.031 0.229,0.167 10 0.5 2.406,2.01 2.531,2.188 0.125,0.177 10 0 3.5,2.021 3.635,2.188 0.135,0.167 10 0 2.594,2.021 2.833,2.177 0.24,0.156 10 -23 2.99,2.021 3.229,2.177 0.24,0.156 10 -13 3.469,2.208 3.656,2.375 0.188,0.167 10 32 4.719,2.021 4.906,2.188 0.188,0.167 10 30 4.719,2.208 4.917,2.365 0.198,0.156 10 86 5.125,2.01 5.427,2.188 0.302,0.177 10 (°C) 5.125,2.198 5.417,2.375 0.292,0.177 10 (°F) 1.844,0.417 2.313,0.604 0.469,0.188 10 (sec.)
*a Light Illumination Duration *b Engine Coolant Temperature


i.

Turn the ignition switch to ON, and then measure the light illumination duration.

Light illumination duration:

Refer to the graph.



ii.

Turn the ignition switch off.

If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.


HINT:

Actual light illumination duration may vary slightly from the graph.




Hide 2.INSPECT PRE-HEATING

a.
A301637
0.26,1.448 0.573,1.604 0.313,0.156 10 false *a 1.781,3.167 2.094,3.323 0.313,0.156 10 false *b 0.51,0.323 0.906,0.5 0.396,0.177 10 false 10.5 0.583,0.865 0.917,1.042 0.333,0.177 10 false 8.4 0.594,1.125 0.99,1.302 0.396,0.177 10 false 7.4 0.594,1.323 0.99,1.5 0.396,0.177 10 false 6.8 0.604,1.885 1,2.063 0.396,0.177 10 false 4.7 0.708,2.448 0.948,2.635 0.24,0.188 10 false 0 0.948,2.854 1.188,3.042 0.24,0.188 10 false 0 1.385,2.844 1.625,3.031 0.24,0.188 10 false 12 1.563,2.844 1.906,3.063 0.344,0.219 10 false 12.5 1.865,2.844 2.208,3.063 0.344,0.219 10 false 13 2.083,2.844 2.427,3.063 0.344,0.219 10 false 13.5 2.5,2.844 2.844,3.063 0.344,0.219 10 false 14.5 2.896,2.823 3.198,3.021 0.302,0.198 10 false (V)
*a Pre-heating Time
*b Battery Voltage


Inspect the pre-heating time.

i.

Turn the ignition switch to ON. Measure how long it takes for battery voltage to be applied to the glow plugs.

Standard Time:
Engine Coolant Temperature Pre-heating Time
40°C (104°F) or higher 1 second
below 40°C (104°F) Refer to the graph
(maximum: 15 seconds)



ii.

Turn the ignition switch off.

If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.




b.

Turn the ignition switch to START. Check that battery voltage is applied to the glow plugs.


c.

While cranking the engine, measure how long it takes for battery voltage to be applied to the glow plugs.

Standard Time:
Engine Coolant Temperature Pre-heating Time
40°C (104°F) or higher 1 second
below 40°C (104°F) Refer to the graph
(maximum: 15 seconds)


If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.



Hide 3.INSPECT AFTER GLOW TIME

a.

Inspect the afterglow time.

A113415
1.25,1.417 1.635,1.625 0.385,0.208 2.594,1.417 2.979,1.625 0.385,0.208 2.677,2.104 2.885,2.875 true 1.125,2.01 1.271,2.906 true 4.135,1.906 4.385,2.125 0.25,0.219 10 false *b 5.198,2.896 5.5,3.063 0.302,0.167 10 false *c 2.5,2.917 3.458,3.115 0.958,0.198 10 false 15 (GREL) (+) 1,2.938 1.698,3.135 0.698,0.198 10 false 7 (E1) (-) 1.323,1.438 1.677,1.615 0.354,0.177 10 false C23 4.271,1.521 4.604,1.677 0.333,0.156 10 false 120 4.427,2.281 4.552,2.448 0.125,0.167 10 false 0 4.594,2.479 4.708,2.635 0.115,0.156 10 false 0 5.125,2.49 5.313,2.646 0.188,0.156 10 false 30 5.802,2.49 6,2.646 0.198,0.156 10 false 40 5.719,2.656 5.99,2.823 0.271,0.167 10 false 104 5.135,2.656 5.323,2.823 0.188,0.167 10 false 86 6.073,2.469 6.375,2.646 0.302,0.177 10 false (°C) 6.083,2.635 6.375,2.792 0.292,0.156 10 false (°F) 4.229,1.271 4.74,1.448 0.51,0.177 10 false (sec.) 2.656,1.438 3.01,1.615 0.354,0.177 10 false G39 1.854,1.031 2.073,1.198 0.219,0.167 10 false *a
*a Component with harness connected (ECM) *b After Glow Time
*c Engine Coolant Temperature - -


i.

After the engine starts, measure how long it takes for battery voltage to be applied to terminals G39-15 (GREL) and C23-7 (E1) of the ECM.

Standard Time:
Tester Connection Specified Condition
G39-15 (GREL) - C23-7 (E1) Refer to the graph


If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.