Home › Engine / Hybrid System › 2KD-FTV STARTING › STARTER(for BOSCH Made)
RM1840EF _51 Engine / Hybrid System _009604 2KD-FTV STARTING _0052429 STARTER(for BOSCH Made) G

2KD-FTV STARTING  STARTER(for BOSCH Made)  INSPECTION  


PROCEDURE

Hide 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may became hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


A121979
3.875,2.615 5.583,1.396 5.583,1.396 6.146,1.396 true 3.604,2.958 3.083,3.26 3.083,3.26 1.552,3.26 false 3.74,2.438 2.021,1.135 2.021,1.135 1.344,1.135 true 6.219,1.292 6.458,1.49 0.24,0.198 10 false *3 1.354,3.188 1.552,3.385 0.198,0.198 10 false *2 1,1.073 1.302,1.271 0.302,0.198 10 false *1
*1 Terminal 30 *2 Terminal 50
*3 Terminal C - -


a.

Perform pull-in test.

i.

Remove the nut, and then disconnect the field coil core from terminal C.


ii.

Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.

A122799
2.542,0.792 2.792,0.958 0.25,0.167 10 *a
*a Operation - -


If the clutch pinion gear does not move, replace the magnet starter switch assembly.



b.

Perform holding test.

i.

When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.

A121976
4.604,1.573 5.906,1.333 5.906,1.333 6.188,1.333 false 4.385,0.896 4.729,1.094 0.344,0.198 10 false *a 6.271,1.24 6.542,1.458 0.271,0.219 10 false *1
*1 Terminal C - -
*a Disconnect - -


If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.

Inspect clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

A121977
2.729,1.125 2.938,1.333 0.208,0.208 10 *b 2.5,0.458 2.75,0.667 0.25,0.208 10 *a
*a Disconnect *b Operation


If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



d.

Perform operation test without load.

i.

Connect the field coil lead wire to terminal C with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Mount the starter in a vise between aluminum plates.


iii.

Connect the battery and ammeter to the starter as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

123 A or less at 11.5 V


A121978
4.083,2.313 3.781,2.594 false 3.781,2.594 3.448,2.594 false 4.229,1.896 4.698,1.354 4.698,1.354 5.229,1.354 true 3.26,2.521 3.563,2.719 0.302,0.198 10 false *2 5.302,1.25 5.563,1.427 0.26,0.177 10 false *1 4.583,2.49 4.802,2.688 0.219,0.198 10 false *a
*1 Terminal 30 *2 Terminal 50
*a Connect - -


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER ARMATURE ASSEMBLY

a.
A082643

Measure the resistance.

i.

Measure the resistance between the segments of the commutator.

Standard resistance:

Below 1.7 Ω


If the result is not as specified, replace the armature assembly.


ii.
A082644

Measure the resistance between a segment of the commutator and armature coil core.

Standard resistance:

10 kΩ or higher


If the result is not as specified, replace the armature assembly.



b.
A082645

Inspect the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Standard runout:

0.02 mm (0.000787 in.)


Maximum runout:

0.04 mm (0.00157 in.)


If the runout is more than the maximum, replace the armature assembly.



c.
A105696

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

32.2 mm (1.278 in.)


Minimum diameter:

31.1 mm (1.235 in.)


If the diameter is less than the minimum, replace the armature assembly.


d.
A105577

Using a vernier caliper, measure the undercut depth of the commutator.

Standard depth:

0.9 mm (0.0354 in.)


Minimum depth:

0.4 mm (0.0157 in.)


If the depth is less than the minimum, replace the armature assembly.


Hide 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A123771

Using a vernier caliper, measure the brush length.

Standard length:

14.0 mm (0.556 in.)


Minimum length:

9.0 mm (0.354 in.)


If the length is less than the minimum, replace the starter brush holder assembly.


b.
A104910
1.385,1.115 0.885,1.115 false 1.542,1.594 0.938,1.594 false 2.427,1.24 2.927,1.24 false 2.219,0.833 2.76,0.833 false 0.74,1.031 0.927,1.24 0.188,0.208 10 A 0.781,1.521 0.979,1.719 0.198,0.198 10 B 2.958,1.167 3.135,1.375 0.177,0.208 10 C 2.802,0.76 2.979,0.99 0.177,0.229 10 D

Check the brush holder.

i.

Measure the resistance between the brushes.

Standard resistance:
Tester Connection Specified Condition
A - B 10 kΩ or higher
A - C 10 kΩ or higher
A - D Below 1 Ω
B - C Below 1 Ω
B - D 10 kΩ or higher
C - D 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.



Hide 4.INSPECT STARTER CLUTCH SUB-ASSEMBLY

A301370
1.448,0.427 1.76,0.625 0.313,0.198 10 *a 1.479,1.49 1.792,1.688 0.313,0.198 10 *b
*a Free
*b Lock


a.

Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter clutch sub-assembly.


b.

Turn the pinion gear by hand while applying inward force and check the movement of the bearing.

If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.


Hide 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A301371
1.281,1.792 1.406,1.792 1.406,1.792 1.583,1.188 false 0.542,1.479 0.531,1.177 false 2.844,1.281 2.719,0.729 2.719,0.729 2.542,0.729 false 0.479,1.521 0.792,1.719 0.313,0.198 10 *1 1.094,1.729 1.406,1.927 0.313,0.198 10 *2 2.375,0.646 2.688,0.844 0.313,0.198 10 *3
*1 Switch Body
*2 Spring
*3 Plunger


Check the plunger.

i.

Install the plunger and spring onto the switch body.


ii.
A104908

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the magnet starter switch assemby.



b.
A121933
1.948,1.031 2.26,0.469 2.26,0.469 2.458,0.469 true 1.604,1.302 0.958,1.531 0.958,1.531 0.958,1.677 true 0.896,1.74 1.146,1.927 0.25,0.188 10 false *2 2.479,0.375 2.708,0.531 0.229,0.156 10 false *1
*1 Terminal 50
*2 Terminal C


Check if the pull-in coil has an open circuit.

i.

Measure the resistance between terminal 50 and terminal C.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A121934
2.052,1.281 2.292,0.74 false 2.292,0.74 2.458,0.74 false 2.479,0.646 2.781,0.875 0.302,0.229 10 *1
*1 Terminal 50


Check if the hold-in coil has an open circuit.

i.

Measure the resistance between terminal 50 and the switch body.

Standard resistance:

Below 2 Ω


If the result is not as specified, replace the magnet starter switch.