Home › Engine / Hybrid System › 2KD-FTV STARTING › STARTER(for BOSCH Made)
RM1840EF _51 Engine / Hybrid System _009604 2KD-FTV STARTING _0052429 STARTER(for BOSCH Made) A

2KD-FTV STARTING  STARTER(for BOSCH Made)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL PLANET CARRIER SHAFT SUB-ASSEMBLY

a.

Install the 3 damper rubbers and the intermediate sealing to the planet carrier.


b.

Install the planet carrier shaft to the planet carrier.


c.

Install the washer to the planet carrier shaft.


d.
A105363

Using a screwdriver and hammer, tap on a new snap ring.


Hide 2.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.
A121935
2.615,1.615 2.656,1.646 false
V100135

MP grease


Apply MP grease to the spline of the starter clutch sub-assembly and planet carrier shaft.


b.

Install the starter clutch to the planet carrier shaft.


c.
A301372
1.833,0.75 1.896,0.219 1.896,0.219 2.042,0.219 false 1.917,1.573 1.917,1.229 false 2.021,1.042 2.042,1.01 false 2.063,0.115 2.375,0.313 0.313,0.198 10 false *1 1.865,1.625 2.177,1.823 0.313,0.198 10 false *2
*1 Snap Ring
*2 Pinion Stop Collar
V100135

MP grease


Apply MP grease to a new snap ring and the pinion stop collar.


d.

Install the pinion stop collar and snap ring.


e.
A104906
2.646,0.563 2.917,1.115 true 1.677,0.115 1.844,0.115 1.844,0.115 2.208,0.479 true 1.49,0.031 1.792,0.229 0.302,0.198 10 false *1 2.875,1.146 3.167,1.344 0.292,0.198 10 false *2
*1 Planet Carrier Shaft
*2 Snap Ring


Using a vise, compress the snap ring.


f.
A033587
0.5,0.729 0.5,1.76 true 0.594,0.667 0.771,1.292 true 0.719,1.323 0.979,1.521 0.26,0.198 10 false *1 0.427,1.781 0.615,1.979 0.188,0.198 10 false *2
*1 Snap Ring
*2 Piston Stop Collar


Using a plastic-faced hammer, lightly tap the planet carrier shaft while holding the outside of the starter clutch sub-assembly by hand until the pinion stop collar and snap ring are as shown in the illustration.


g.
A198324
1.271,0.354 1.333,0.375 false
V100135

MP grease


Apply MP grease to the pinion drive lever.


h.

Install the starter clutch sub-assembly, pinion drive lever and cover to the starter drive housing.


i.
A198325
1.646,1.625 1.604,1.677 false
V100135

MP grease


Apply MP grease to the planetary gears and pin parts of the planet carrier shaft.


j.

Install the 3 planetary gears to the planet carrier.


Hide 3.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature to the starter yoke.


Hide 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

NOTICE:

Do not drop the starter armature assembly.


a.
A200784
2.948,0.833 3.24,0.198 false 3.24,0.198 3.052,0.198 false 0.771,1.031 1.125,1.281 1.125,1.281 1.125,1.458 true 0.417,0.365 0.417,0.208 0.417,0.208 0.729,0.208 true 2.844,0.135 3.094,0.313 0.25,0.177 10 false *3 1.052,1.531 1.26,1.708 0.208,0.177 10 false *2 0.75,0.115 0.969,0.313 0.219,0.198 10 false *1
*1 Rubber Part
*2 Brush Holder
*3 Spring


Hold the starter yoke assembly between aluminum plates in a vise.

NOTICE:

Do not damage the starter yoke.



b.

While compressing the springs, install the starter brush holder to the starter armature.

NOTICE:

Align the cutout of the starter yoke and the rubber part and install the starter brush holder.



c.

Install the starter commutator end frame to the starter yoke.


d.

Install the washer to the starter commutator end frame.


e.

Apply MP grease to the slotted washer and install it.


f.

Install the seal ring.


g.

Install the starter commutator end frame cover to the starter commutator end frame with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


Hide 5.INSTALL STARTER YOKE ASSEMBLY

a.
A121936
1.521,1.729 1.813,0.698 true 1.813,0.698 1.729,2.115 true 2.094,1.688 1.813,0.698 true 1.75,0.531 1.979,0.729 0.229,0.198 10 false *1
*1 Claw


Fit the 3 claws of the plate into the 3 grooves of the planet carrier to install the plate to the planet carrier.


b.

Install the cover ring to the planet carrier.


c.
A121937
1.74,1.031 1.052,1.5 1.052,1.5 1.052,1.719 true 1.365,0.604 1.604,0.427 1.604,0.427 1.802,0.427 false 1.906,0.333 2.167,0.521 0.26,0.188 10 false *1 1,1.792 1.24,1.969 0.24,0.177 10 false *2
*1 Starter Drive Housing Cover
*2 Groove


Align the groove of the starter yoke assembly and the starter drive housing cover and install the starter yoke assembly to the starter drive housing.


d.

Install the 2 bolts.

Torque:
4.8 N*m (48 kgf*cm, 42 in.*lbf)


Hide 6.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.

Apply MP grease to the hook.


b.

Install the plunger to the pinion drive lever.


c.

Install the return spring to the magnet starter switch assembly.


d.

Using a T25 "TORX" socket wrench, install the magnet starter switch assembly with the 3 screws.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


e.

Connect the lead wire to terminal C with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)