Home › Engine / Hybrid System › 2KD-FTV STARTING › PRE-HEATING SYSTEM(w/ DPF) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009604 2KD-FTV STARTING _0052430 PRE-HEATING SYSTEM(w/ DPF) G

2KD-FTV STARTING  PRE-HEATING SYSTEM(w/ DPF)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch off for 60 seconds before performing the following inspections.


PROCEDURE

Hide 1.INSPECT ILLUMINATION DURATION OF GLOW INDICATOR LIGHT

a.
A301596
1.604,1.417 1.917,1.615 0.313,0.198 10 false *c 0.313,0.948 0.729,1.135 0.417,0.188 10 false (sec.) 0.427,1.302 0.583,1.49 0.156,0.188 10 false 7 0.427,1.469 0.583,1.656 0.156,0.188 10 false 6 0.417,1.844 0.573,2.031 0.156,0.188 10 false 3 0.229,2.115 0.563,2.271 0.333,0.156 10 false 0.45 0.76,2.344 1.052,2.5 0.292,0.156 10 false -25 0.76,2.573 1.052,2.729 0.292,0.156 10 false -13 1.177,2.354 1.469,2.51 0.292,0.156 10 false -15 1.281,2.573 1.573,2.729 0.292,0.156 10 false 5 1.823,2.344 2.115,2.5 0.292,0.156 10 false 0 1.802,2.552 2.094,2.708 0.292,0.156 10 false 32 2.698,2.604 2.99,2.76 0.292,0.156 10 false 68 2.708,2.354 3,2.51 0.292,0.156 10 false 20 3.052,2.344 3.385,2.583 0.333,0.24 10 false (°C) 3.052,2.604 3.406,2.854 0.354,0.25 10 false (°F) 1.573,2.906 1.885,3.104 0.313,0.198 10 false *b 0.177,0.729 0.49,0.927 0.313,0.198 10 false *a
*a Glow Indicator Light Illumination Time
*b Engine Coolant Temperature
*c When atmospheric pressure is 100 kPa (1.0 kgf/cm2)


Turn the ignition switch to ON and measure the length of time that the light remains illuminated.

Light illumination duration:

Refer to the graph


HINT:

Depending on the engine coolant temperature, the indicator light illumination time changes as shown in the illustration.



Hide 2.INSPECT PRE-HEATING FUNCTION

a.

Measure the voltage applied to the glow plugs.

Standard voltage:

11 to 14 V at 25°C (77°F) or less



b.

Measure the length of time that voltage is applied to the glow plugs while the ignition switch is ON.

Standard Pre-heating Time:
Condition Pre-heating Time
Battery voltage at 14.5 V or higher 1 second
Engine coolant temperature 40°C (104°F) or higher 1 second
Other than above 15 seconds



Hide 3.INSPECT AFTER GLOW

a.

Measure the voltage applied to the glow plugs after the engine is started.

Standard Voltage:
Measurement Condition Specified Condition
Engine coolant temperature 20°C (68°F) or less 11 to 14 V
Engine coolant temperature 20°C (68°F) to 41°C (106°F) 0 to 14 V
Engine coolant temperature 41°C (106°F) or higher 0 V


HINT:

The maximum amount of time that voltage is applied to the glow plugs is 20 minutes.