Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER(for 1.6 kW Type) › 2011.10–2013.10
RM1840EF _51 Engine / Hybrid System _009605 2TR-FE STARTING _0052434 STARTER(for 1.6 kW Type) A

2TR-FE STARTING  STARTER(for 1.6 kW Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Use high-temperature grease to lubricate the bearings and sliding parts when assembling the starter.


PROCEDURE

Hide 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A196356
1.406,1.667 1.5,1.792 0.094,0.125 6 false .
V100135

High-temperature Grease


Apply high-temperature grease to the starter drive lever set pin.


b.
A301344
1.24,2.167 1.49,2.167 1.49,2.167 1.49,1.792 false 1.573,0.885 1.896,0.885 false 1.417,0.802 1.729,1 0.313,0.198 10 *1 1.073,2.073 1.385,2.271 0.313,0.198 10 *2
*1 Drive Lever Set Pin
*2 Starter Center Bearing Clutch


Install the drive lever set pin to the starter center bearing clutch sub-assembly.


c.

Install the starter center bearing clutch and drive lever set pin together to the starter drive housing.


Hide 2.INSTALL PLANETARY GEAR

a.
A196359
1.792,1.333 1.885,1.458 0.094,0.125 6 false .
V100135

High-temperature Grease


Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.


b.

Install the 3 planetary gears onto the pins of the planetary shaft.


Hide 3.INSTALL STARTER ARMATURE ASSEMBLY

NOTICE:

Do not drop the starter armature assembly.


a.
A196357
1.531,1.865 1.313,1.635 1.313,1.635 0.927,1.635 true 1.604,0.75 1.229,0.75 false 1.604,0.271 1.229,0.271 false 0.729,1.563 0.958,1.719 0.229,0.156 10 false *3 1.021,0.688 1.323,0.833 0.302,0.146 10 false *2 1.021,0.198 1.292,0.354 0.271,0.156 10 false *1
*1 Snap Ring
*2 Plate Washer
*3 Bearing
V100135

High-temperature Grease


Apply high-temperature grease to the plate washer, a new snap ring and the bearing.


b.

Mount the starter commutator end frame in a vise between aluminum plates.

NOTICE:

Do not damage the starter commutator end frame.



c.
A196360
1.104,1.188 1.198,1.313 0.094,0.125 6 false .
V100135

High-temperature Grease


Apply high-temperature grease to the starter armature assembly.


d.

Install the starter armature assembly to the starter commutator end frame assembly.


e.

Install the plate washer to the starter armature shaft.


f.

Using snap ring pliers, install the snap ring.

NOTICE:
·

Be sure to install the snap ring in the armature shaft groove securely.

·

Be sure to properly install the snap ring because it easily expands.




g.
A058810
1.573,0.219 1.771,0.406 0.198,0.188 10 *1
*1 Length


Check the snap ring length.

i.

Using a vernier caliper, measure the snap ring length.

Maximum length:

5.0 mm (0.197 in.)


If the length is more than the maximum, replace the snap ring.



Hide 4.INSTALL STARTER COMMUTATOR END FRAME COVER

a.

Install the commutator end frame cover into the starter commutator end frame.


Hide 5.INSTALL STARTER ARMATURE PLATE

a.
A073991
2.281,0.438 2.156,0.438 2.156,0.438 1.823,0.823 true 0.333,1.156 0.031,0.323 0.031,0.323 0.219,0.323 false 0.24,0.25 0.448,0.427 0.208,0.177 10 false *2 2.313,0.365 2.521,0.521 0.208,0.156 10 false *1
*1 key
*2 Keyway


Align the keyway of the starter armature plate with the key inside the starter yoke, and install the starter armature plate.


Hide 6.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
G037250
1.635,0.75 0.865,0.323 0.865,0.323 0.708,0.323 false 2.208,0.552 1.635,0.073 1.635,0.073 1.479,0.073 false 1.281,0 1.448,0.156 0.167,0.156 10 *1 0.542,0.25 0.719,0.396 0.177,0.146 10 *2
*1 Rubber Part
*2 Groove


Align the rubber part on the starter commutator end frame with the groove of the starter yoke.


b.

Install the starter commutator end frame to the starter yoke.

NOTICE:

The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed, causing the magnet to break.



Hide 7.INSTALL STARTER YOKE ASSEMBLY

a.
G037251
2.479,0.833 2.365,0.833 2.365,0.833 1.99,1.156 false 1.01,0.573 1.198,0.573 1.198,0.573 1.563,0.99 false 2.51,0.75 2.896,0.906 0.385,0.156 10 *2 0.854,0.5 1.135,0.656 0.281,0.156 10 *1
*1 Groove
*2 Claw


Align the claw of the starter yoke with the groove inside the starter drive housing.


b.

Install the starter yoke with the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 8.INSTALL REPAIR SERVICE STARTER KIT

a.
A196358
2.104,0.958 2.198,1.083 0.094,0.125 6 false .
V100135

High-temperature Grease


Apply high-temperature grease to the plunger and hook.


b.

Hang the plunger hook of the repair service starter kit on the drive lever set pin.


c.
G037613

Install the plunger and return spring.


d.

Install the repair service starter kit with the 2 screws.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)


e.

Connect the lead wire to the terminal with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)