Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER(for 1.7 kW Type)
RM1840EF _51 Engine / Hybrid System _009605 2TR-FE STARTING _0052437 STARTER(for 1.7 kW Type) G

2TR-FE STARTING  STARTER(for 1.7 kW Type)  INSPECTION  


PROCEDURE

Hide 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.
A236745
2.25,1.375 2.25,2.344 2.25,2.344 2.094,2.344 true 2.333,1.177 1.781,0.219 1.781,0.219 1.656,0.219 true 1.917,2.26 2.156,2.427 0.24,0.167 10 false *2 1.5,0.135 1.781,0.344 0.281,0.208 10 false *1
*1 Terminal 50
*2 Terminal C
V100135

Moves outward


Perform a pull-in test.

i.

Remove the nut, and then disconnect the lead wire from terminal C.


ii.

Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



c.
A236746
2.021,1.573 1.354,2.25 1.354,2.25 1.25,2.25 true 1.094,2.177 1.354,2.365 0.26,0.188 10 false *1
*1 Terminal C
V100135

Disconnect


Perform a holding test.

i.

Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



d.
A301378
0.573,1.229 0.667,1.271 false
V100135

Disconnect
V100136

Returns inward


Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.
A236748
2.698,1.208 2.49,0.406 2.49,0.406 2.354,0.406 false 2.469,1.323 2.281,2.281 2.281,2.281 2.188,2.281 false 2.01,2.198 2.281,2.417 0.271,0.219 10 false *2 2.188,0.323 2.417,0.521 0.229,0.198 10 false *1
*1 Terminal 30
*2 Terminal 50


Connect the battery and an ammeter to the starter as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

90 A or less at 10.9 V


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

If necessary, replace the starter armature assembly.


b.
A122024
1.802,1.354 1.802,1.948 1.802,1.948 1.656,1.948 false 1.479,1.875 1.74,2.063 0.26,0.188 10 *1
*1 Segment


Inspect the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connector Condition Specified Condition
Segment - Segment Always 3.0 to 3.3 Ω


If the result is not as specified, replace the starter armature assembly.



c.
A122025
2.146,1.167 2.531,0.375 2.531,0.375 2.625,0.375 false 1.25,0.906 0.927,1.292 0.927,1.292 0.823,1.292 false 2.656,0.281 3.021,0.604 0.365,0.323 10 false *1 0.615,1.208 0.885,1.417 0.271,0.208 10 false *2
*1 Segment
*2 Coil Core


Inspect the commutator for short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connector Condition Specified Condition
Segment - Coil Core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A122026

Check the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Standard circle runout:

0.02 mm (0.000787 in.)


Maximum circle runout:

0.04 mm (0.00157 in.)


If the circle runout is more than the maximum, correct the circle runout with sandpaper (No. 400) or replace the starter armature assembly.



e.
A122027
0.24,0.641 0.397,0.794 0.156,0.153 10 *1
*1 Diameter


Check the commutator diameter.

i.

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

32.2 mm (1.27 in.)


Minimum diameter:

31.1 mm (1.22 in.)


If the diameter is less than the minimum, replace the starter armature assembly.



f.
A122028

Check the undercut depth.

i.

Using a vernier caliper, measure the undercut depth of the commutator.

Standard depth:

0.9 mm (0.0354 in.)


Minimum depth:

0.4 mm (0.0157 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.



Hide 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A122029
2.56,0.829 2.734,0.975 0.174,0.146 10 *1
*1 Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard length:

11.3 mm (0.445 in.)


Minimum length:

7.5 mm (0.295 in.)


If the length is less than the minimum, replace the starter brush holder assembly.



b.
A122030
2.354,1.281 2.875,1.281 false 2.094,0.844 2.677,0.844 false 1.229,1.146 0.76,1.146 false 1.438,1.583 0.896,1.583 false 0.635,1.052 0.813,1.25 0.177,0.198 10 false A 2.74,0.74 3.031,1.021 0.292,0.281 10 false D 2.917,1.198 3.135,1.448 0.219,0.25 10 false C 0.74,1.49 1.073,1.802 0.333,0.313 10 false B

Inspect the brush insulation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A - B
A - C
B - D
C - D
Always 10 kΩ or higher
A - D
B - C
Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.



Hide 4.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A251380
1.427,0.854 1.417,0.958 false
V100135

Free
V100136

Lock


Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter clutch sub-assembly.


Hide 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A122032
0.625,1.115 0.625,1.604 0.625,1.604 0.479,1.604 false 2.677,0.688 2.823,0.688 2.823,0.688 2.823,1.417 false 1.542,0.365 1.688,0.365 1.688,0.365 1.688,1.094 false 0.313,1.521 0.583,1.729 0.271,0.208 10 false *1 1.385,0.271 1.677,0.49 0.292,0.219 10 false *2 2.521,0.604 2.76,0.792 0.24,0.188 10 false *3
*1 Switch Body
*2 Spring
*3 Plunger


Check the plunger.

i.

Install the plunger and spring to the switch body.


ii.
A122033

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the magnet starter switch assembly.



b.
A122034
1.958,1.635 1.958,1.99 1.958,1.99 1.802,1.99 false 2.073,1.219 2.073,0.24 2.073,0.24 1.979,0.24 false 1.625,1.906 1.917,2.125 0.292,0.219 10 *2 1.792,0.156 2.052,0.354 0.26,0.198 10 *1
*1 Terminal 50
*2 Terminal C


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A122035
2.073,1.219 2.073,0.375 2.073,0.375 2.302,0.375 false 1.156,0.625 1.156,0.188 1.156,0.188 1.052,0.188 false 2.313,0.292 2.677,0.521 0.365,0.229 10 *1 0.896,0.094 1.156,0.323 0.26,0.229 10 *2
*1 Terminal 50
*2 Switch Body


Measure the resistance according to the value(s) in the table below.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.