Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER(for 1.7 kW Type)
RM1840EF _51 Engine / Hybrid System _009605 2TR-FE STARTING _0052437 STARTER(for 1.7 kW Type) A

2TR-FE STARTING  STARTER(for 1.7 kW Type)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A122007

Remove the nut, and then disconnect the lead wire from terminal C.


b.
A122008

Using a T25 "TORX" socket wrench, remove the 3 screws holding the magnet starter switch to the starter drive housing.


c.

Remove the magnet starter switch.


d.

Remove the spring.


e.
A122009
2.448,0.396 2.281,0.396 false 2.281,0.396 1.938,0.615 false 1.01,0.458 1.49,0.458 false 0.813,0.365 1.094,0.552 0.281,0.188 10 *2 2.49,0.302 2.802,0.542 0.313,0.24 10 *1
*1 Plunger
*2 Pinion Drive Lever


Remove the plunger from the pinion drive lever.


Hide 2.REMOVE STARTER YOKE ASSEMBLY

a.
A122010

Remove the 2 bolts and starter yoke from the starter drive housing.


b.
A122011

Remove the cover ring and plate from the planet carrier.


Hide 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A122012

Hold the starter yoke assembly between aluminum plates in a vise.

NOTICE:

Do not damage the starter yoke assembly.



b.

Remove the 2 screws and starter commutator end frame cover from the starter commutator end frame.


c.
A122013
1.958,0.333 1.813,0.333 1.813,0.333 1.521,0.688 false 1.979,0.25 2.167,0.448 0.188,0.198 10 false *1
*1 Slotted Washer


Remove the slotted washer.


d.
A122014
1.604,1.875 1.604,1.406 false 1.604,1.438 1.604,1.406 false 2.552,0.604 2.396,0.604 2.396,0.604 1.781,0.865 false 2.583,0.5 2.844,0.708 0.26,0.208 10 false *1 1.552,1.906 1.792,2.104 0.24,0.198 10 false *2
*1 Washer
*2 Commutator End Frame


Remove the washer.


e.

Remove the starter commutator end frame from the starter yoke.


f.
A301377
0.604,0.573 0.604,0.167 0.604,0.167 0.771,0.167 true 0.719,1.542 0.865,1.542 0.865,1.542 0.865,1.052 true 2.823,0.896 3.104,0.375 3.104,0.375 2.927,0.375 false 0.813,0.073 1.073,0.26 0.26,0.188 10 false *1 0.552,1.448 0.802,1.646 0.25,0.198 10 false *2 2.76,0.292 3.073,0.49 0.313,0.198 10 false *3
*1 Rubber Part
*2 Brush Holder
*3 Spring


Remove the starter brush holder from the starter armature.

NOTICE:

Do not pull on the rubber part.



Hide 4.REMOVE STARTER ARMATURE ASSEMBLY

a.
A122016
1.979,0.438 1.208,0.438 false 1.573,1.688 2.063,1.688 false 2.021,0.333 2.281,0.542 0.26,0.208 10 *1 1.427,1.604 1.656,1.823 0.229,0.219 10 *2
*1 Starter Yoke
*2 Starter Armature


Remove the starter armature from the starter yoke.


Hide 5.REMOVE STARTER CLUTCH SUB-ASSEMBLY

a.
A122017

Remove the 3 planetary gears from the planet carrier.


b.
A122018
0.938,2.74 0.938,3.406 0.938,3.406 0.792,3.406 false 2.156,3.281 2.156,4 2.156,4 2.01,4 false 2.833,0.615 3.052,0.615 3.052,0.615 2.896,1.74 false 1.625,0.427 1.865,0.427 1.865,0.427 2.219,1.031 false 1.469,0.344 1.677,0.542 0.208,0.198 10 *1 2.677,0.531 2.958,0.75 0.281,0.219 10 *2 0.635,3.323 0.938,3.531 0.302,0.208 10 *3 1.865,3.927 2.094,4.115 0.229,0.188 10 *4
*1 Pinion Drive Lever
*2 Cover
*3 Starter Drive Housing
*4 Starter Center Bearing Clutch


Remove the starter center bearing clutch, pinion drive lever and cover from the starter drive housing.


c.
A122019
0.729,0.656 1.51,0.656 false 2.625,0.802 2.51,0.802 2.51,0.802 2.052,1.188 false 0.552,0.552 0.823,0.771 0.271,0.219 10 *1 2.646,0.719 2.917,0.958 0.271,0.24 10 *2
*1 Collar
*2 Clutch


Using a screwdriver, move the pinion stop collar toward the starter clutch.


d.
A122020
2.094,0.542 1.708,0.542 false 1.052,0.479 1.198,0.479 1.198,0.479 1.448,0.729 false 2.135,0.448 2.406,0.688 0.271,0.24 10 false *1 0.854,0.396 1.146,0.573 0.292,0.177 10 false *2
*1 Snap Ring
*2 Collar


Using a screwdriver, remove the snap ring.


e.
A122021

Remove the pinion stop collar and starter clutch from the planet carrier shaft.


Hide 6.REMOVE PLANET CARRIER SHAFT SUB-ASSEMBLY

a.
A122022

Using 2 screwdrivers and a hammer, tap off the snap ring from the planet carrier shaft.


b.

Remove the washer from the planet carrier shaft.


c.
A122023
1.958,0.49 1.396,0.49 false 1.854,1.333 1.615,1.583 1.615,1.583 1.469,1.583 false 2,0.396 2.302,0.604 0.302,0.208 10 *1 1.302,1.49 1.563,1.729 0.26,0.24 10 *2
*1 Planet Carrier
*2 Planet Carrier Shaft


Remove the planet carrier shaft from the planet carrier.


d.

Remove the intermediate sealing and 3 damper rubbers from the planet carrier.