Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER(for 1.7 kW Type)
RM1840EF _51 Engine / Hybrid System _009605 2TR-FE STARTING _0052437 STARTER(for 1.7 kW Type) A

2TR-FE STARTING  STARTER(for 1.7 kW Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Use high-temperature grease to lubricate the bearings and sliding parts when assembling the starter.


PROCEDURE

Hide 1.INSTALL PLANET CARRIER SHAFT SUB-ASSEMBLY

a.

Install the 3 damper rubbers and intermediate sealing to the planet carrier.


b.

Install the planet carrier shaft to the planet carrier.


c.

Install the washer to the planet carrier shaft.


d.
A122037

Using a screwdriver and hammer, tap on a new snap ring.


Hide 2.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.
A236853
0.896,0.865 0.927,0.875 false
V100135

High-temperature Grease


Apply high-temperature grease to the splines of the starter clutch and planet carrier shaft.


b.

Install the starter clutch to the planet carrier shaft.


c.
A236854
1.771,0.646 1.99,0.115 1.99,0.115 2.073,0.115 false 1.833,1.125 1.927,1.333 1.927,1.333 2.01,1.333 false 1.875,0.927 1.917,0.885 false 2.104,0.031 2.385,0.219 0.281,0.188 10 false *1 2.031,1.25 2.396,1.458 0.365,0.208 10 false *2
*1 Snap Ring
*2 Pinion Stop Collar
V100135

High-temperature Grease


Apply high-temperature grease to a new snap ring and the pinion stop collar.


d.

Install the pinion stop collar and snap ring as show in the illustration.


e.
A122040
1.677,0.156 1.844,0.156 1.844,0.156 2.198,0.635 false 2.542,0.75 2.542,1.625 2.542,1.625 2.76,1.625 false 1.531,0.073 1.75,0.25 0.219,0.177 10 *1 2.792,1.542 3.01,1.719 0.219,0.177 10 *2
*1 Planet Carrier Shaft
*2 Snap Ring


Using a vise, compress the snap ring between aluminum plates.


f.
A122041
0.615,0.354 0.542,0.354 0.542,0.354 0.542,0.677 false 0.49,0.75 0.49,1.49 0.49,1.49 0.635,1.49 false 0.656,0.25 0.917,0.552 0.26,0.302 10 false *1 0.656,1.385 0.885,1.615 0.229,0.229 10 false *2
*1 Snap Ring
*2 Pinion Stop Collar


Using a plastic-faced hammer, lightly tap the planet carrier shaft while holding the outside of the starter clutch sub-assembly by hand until the pinion stop collar and snap ring are as shown in the illustration.


g.
A236855
1.375,0.396 1.26,0.365 false
V100135

High-temperature Grease


Apply high-temperature grease to the pinion drive lever.


h.

Install the starter center bearing clutch, pinion drive lever and cover to the starter drive housing.


i.
A236856
2.698,1.271 2.667,1.292 false
V100135

High-temperature Grease


Apply high-temperature grease to the planetary gears and the pins of the planet carrier shaft.


j.

Install the 3 planetary gears to the planet carrier.


Hide 3.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature to the starter yoke.


Hide 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Hold the starter yoke between aluminum plates in a vise.

NOTICE:

Do not damage the starter yoke.



b.

While compressing the springs, install the starter brush holder to the armature.

NOTICE:

Align the cutout of the starter yoke and the rubber part and install the brush holder.



c.

Install the commutator end frame to the starter yoke.


d.

Install the washer to the commutator end frame.


e.

Apply high-temperature grease to the slotted washer.


f.

Install the slotted washer.


g.

Install the commutator end frame cover to the commutator end frame with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


Hide 5.INSTALL STARTER YOKE ASSEMBLY

a.
A122049
1.698,0.135 1.542,0.135 1.542,0.135 1.542,1.167 false 2.24,0.458 2.323,0.458 false 2.323,0.458 2.052,1.594 false 1.646,1.365 1.344,1.802 false 1.344,1.802 1.594,1.854 false 1.094,1.469 0.469,1.656 false 0.469,1.656 1.219,0.969 false 2.073,0.354 2.323,0.594 0.25,0.24 10 false *2 1.719,0.031 2.021,0.219 0.302,0.188 10 false *1 0.344,1.677 0.531,1.833 0.188,0.156 10 false *1 1.167,1.719 1.417,1.948 0.25,0.229 10 false *2
*1 Groove
*2 Claw


Fit the 3 claws of the plate into the 3 grooves of the planet carrier to install the plate to the planet carrier.


b.

Install the cover ring.


c.
A122050
1.542,0.656 1.146,0.26 1.146,0.26 1,0.26 false 2.156,0.708 2.042,0.708 2.042,0.708 2.042,1.146 false 2.188,0.615 2.396,0.823 0.208,0.208 10 false *2 0.844,0.167 1.063,0.385 0.219,0.219 10 false *1
*1 Starter Drive Housing Cover
*2 Groove


Align the groove of the yoke and the starter drive housing cover and install the starter yoke to the starter drive housing.


d.

Install the 2 bolts.

Torque:
4.8 N*m (48 kgf*cm, 42 in.*lbf)


Hide 6.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A122052
1.104,0.167 1.208,0.167 1.208,0.167 1.5,0.458 false 2.281,0.375 2.167,0.375 2.167,0.375 1.927,0.615 false 2.323,0.26 2.552,0.479 0.229,0.219 10 false *2 0.938,0.052 1.167,0.24 0.229,0.188 10 false *1
*1 Pinion Drive Lever
*2 Plunger
V100135

High-temperature Grease


Apply high-temperature grease to the hook of the plunger.


b.

Install the plunger to the pinion drive lever.


c.

Install the return spring to the magnet starter switch.


d.

Using a T25 "TORX" socket wrench, install the magnet starter switch with the 3 screws.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


e.

Connect the lead wire to terminal C with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)