1.INSPECT STARTER ASSEMBLY
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.
The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.
Mount the starter in a vise between aluminum plates.
Perform a pull-in test.
| *1 | Terminal 50 |
| *2 | Terminal C |
|
Moves outward |
Remove the nut, and then disconnect the lead wire from terminal C.
Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.
If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.
| *1 | Terminal C |
|
Disconnect |
Perform a holding test.
Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.
If the clutch pinion gear returns inward, replace the magnet starter switch assembly.
|
Disconnect |
|
Returns inward |
Inspect the clutch pinion gear return.
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.
Perform an operation test without load.
Connect the lead wire to terminal C.
| *1 | Terminal 30 |
| *2 | Terminal 50 |
Connect the battery and an ammeter to the starter as shown in the illustration.
Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.
90 A or less at 10.9 V
If the result is not as specified, replace the starter assembly.
2.INSPECT STARTER ARMATURE ASSEMBLY
Check the commutator for dirt and burns on the surface.
If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
If necessary, replace the starter armature assembly.
| *1 | Segment |
Inspect the commutator for an open circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
|---|---|---|
| Segment - Segment | Always | 3.0 to 3.3 Ω |
If the result is not as specified, replace the starter armature assembly.
| *1 | Segment |
| *2 | Coil Core |
Inspect the commutator for short circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
|---|---|---|
| Segment - Coil Core | Always | 10 kΩ or higher |
If the result is not as specified, replace the starter armature assembly.
Check the commutator circle runout.
Place the commutator on V-blocks.
Using a dial indicator, measure the circle runout.
0.02 mm (0.000787 in.)
0.04 mm (0.00157 in.)
If the circle runout is more than the maximum, correct the circle runout with sandpaper (No. 400) or replace the starter armature assembly.
| *1 | Diameter |
Check the commutator diameter.
Using a vernier caliper, measure the commutator diameter.
32.2 mm (1.27 in.)
31.1 mm (1.22 in.)
If the diameter is less than the minimum, replace the starter armature assembly.
Check the undercut depth.
Using a vernier caliper, measure the undercut depth of the commutator.
0.9 mm (0.0354 in.)
0.4 mm (0.0157 in.)
If the undercut depth is less than the minimum, replace the starter armature assembly.
3.INSPECT STARTER BRUSH HOLDER ASSEMBLY
| *1 | Length |
Check the brush length.
Using a vernier caliper, measure the brush length.
11.3 mm (0.445 in.)
7.5 mm (0.295 in.)
If the length is less than the minimum, replace the starter brush holder assembly.
Inspect the brush insulation.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A - B
A - C B - D C - D |
Always | 10 kΩ or higher |
| A - D
B - C |
Below 1 Ω |
If the result is not as specified, replace the starter brush holder assembly.
4.INSPECT STARTER CLUTCH SUB-ASSEMBLY
|
Free |
|
Lock |
Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
If the result is not as specified, replace the starter clutch sub-assembly.
5.INSPECT MAGNET STARTER SWITCH ASSEMBLY
| *1 | Switch Body |
| *2 | Spring |
| *3 | Plunger |
Check the plunger.
Install the plunger and spring to the switch body.
Push in the plunger and check that it returns quickly to its original position.
If the result is not as specified, replace the magnet starter switch assembly.
| *1 | Terminal 50 |
| *2 | Terminal C |
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 50 - Terminal C | Always | Below 1 Ω |
If the result is not as specified, replace the magnet starter switch assembly.
| *1 | Terminal 50 |
| *2 | Switch Body |
Measure the resistance according to the value(s) in the table below.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 50 - Switch body | Always | Below 2 Ω |
If the result is not as specified, replace the magnet starter switch assembly.