Home › Engine / Hybrid System › 1GR-FE STARTING › STARTER › from 2012.04
RM1840EF _51 Engine / Hybrid System _009607 1GR-FE STARTING _0052443 STARTER G

1GR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A251361
2.563,0.417 2.781,0.198 2.781,0.198 3.031,0.198 false 2.344,0.729 1.896,1.521 1.896,1.521 1.635,1.521 true 3.052,0.125 3.219,0.302 0.167,0.177 10 false *1 1.458,1.438 1.625,1.615 0.167,0.177 10 false *2
*1 Terminal 50
*2 Terminal C
V100135

Moves Outward


Connect the battery to the starter as shown in the illustration. Then check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move, replace the repair service starter kit.



c.

Perform a holding test.

i.
A251362
1.396,1.396 1.552,1.396 1.552,1.396 2.104,0.75 true 1.198,1.313 1.365,1.458 0.167,0.146 10 false *1
*1 Terminal C
V100135

Disconnect


Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

If the clutch pinion gear moves inward, replace the repair service starter kit.



d.

Inspect clutch pinion gear return.

i.
A251363
0.792,1.469 0.833,1.406 false
V100135

Disconnect
V100136

Returns Inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the repair service starter kit.



e.
A251364
1.354,1.365 1.563,1.365 1.563,1.365 2.406,0.521 true 2.906,0.365 2.75,0.365 2.75,0.365 2.573,0.542 false 1.167,1.271 1.344,1.427 0.177,0.156 10 false *1 2.948,0.281 3.125,0.438 0.177,0.156 10 false *2
*1 Terminal 30
*2 Terminal 50
V100135

Connect


Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the battery and an ammeter to the starter as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

If necessary, replace the starter armature assembly.


b.

Inspect the commutator for an open circuit.

i.
A073983
1.792,0.313 1.646,0.313 1.646,0.313 1.438,1.104 true 1.865,0.208 2.042,0.385 0.177,0.177 10 false *1
*1 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for a short circuit.

i.
A073984
0.604,1.594 0.854,1.594 0.854,1.594 1.219,1.344 false 2.49,0.417 2.354,0.417 false 2.354,0.417 2.094,1.042 true 2.563,0.333 2.74,0.521 0.177,0.188 10 false *1 0.438,1.5 0.615,1.677 0.177,0.177 10 false *2
*1 Coil Core
*2 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Coil core - Segment Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A097774
1.865,1.792 2.26,1.854 0.396,0.063 2.333,1.521 2.469,1.521 2.469,1.521 2.677,1.854 false 2.24,1.792 2.24,1.854 false 2.521,1.854 1.854,1.854 false 2.115,1.438 2.302,1.594 0.188,0.156 10 false *1
*1 Length


Using a vernier caliper, measure the protrusion length.

Standard length:

3.1 mm (0.122 in.)


Maximum length:

3.8 mm (0.150 in.)


If the length is more than the maximum, replace the starter armature assembly.


Hide 3.INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

a.

Check the brush length.

i.
A076677
2.854,0.792 3.031,0.979 0.177,0.188 10 false *1
*1 Length


Using a vernier caliper, measure the brush length.

Standard exposed length:

9.0 mm (0.354 in.)


Minimum exposed length:

4.0 mm (0.158 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.



b.

Check the resistance.

i.
A073986

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, replace the starter commutator end frame assembly.



Hide 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth on the planetary gear, internal gear and pinion gear of the starter center bearing clutch for wear or damage.

If any of the gears is damaged, replace the starter center bearing clutch sub-assembly.


b.
A251384
1.333,0.604 1.427,0.729 0.094,0.125 6 false .
V100135

Free
V100136

Lock


Hold the starter clutch and rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter center bearing clutch sub-assembly.


Hide 5.INSPECT REPAIR SERVICE STARTER KIT

a.
A058586

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the repair service starter kit.



b.

Check the resistance.

i.
A082691
1.75,0.948 2.021,0.521 2.021,0.521 2.229,0.521 true 1.604,1.375 1.323,1.75 1.323,1.75 1.156,1.75 true 0.938,1.646 1.135,1.844 0.198,0.198 10 false *2 2.271,0.417 2.438,0.615 0.167,0.198 10 false *1
*1 Terminal C
*2 Terminal 50


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the repair service starter kit.


ii.
A082692
1.604,1.365 1.365,1.75 1.365,1.75 1.188,1.75 true 0.969,1.656 1.177,1.854 0.208,0.198 10 false *1
*1 Terminal 50


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Repair service starter kit body Always Below 2 Ω


If the result is not as specified, replace the repair service starter kit.