Home › Engine / Hybrid System › 1GR-FE STARTING › STARTER › from 2012.04
RM1840EF _51 Engine / Hybrid System _009607 1GR-FE STARTING _0052443 STARTER A

1GR-FE STARTING  STARTER  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Use high-temperature grease to lubricate the bearings and sliding parts when assembling the starter.


PROCEDURE

Hide 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A196356
1.406,1.667 1.5,1.792 0.094,0.125 6 false .
V100135

High-temperature Grease


Apply high-temperature grease to the drive lever set pin.


b.
A301344
1.24,2.167 1.49,2.167 1.49,2.167 1.49,1.792 false 1.573,0.885 1.896,0.885 false 1.417,0.802 1.729,1 0.313,0.198 10 *1 1.073,2.073 1.385,2.271 0.313,0.198 10 *2
*1 Drive Lever Set Pin
*2 Starter Center Bearing Clutch


Install the drive lever set pin to the starter center bearing clutch.


c.

Install the starter center bearing clutch together with the drive lever set pin to the starter drive housing.


Hide 2.INSTALL PLANETARY GEAR

A197984
1.896,1.448 1.938,1.427 false
V100135

High-temperature Grease


a.

Apply high-temperature grease to the planetary gears and pin parts of the planet shaft.


b.

Install the 3 planetary gears onto the pins of the planet shaft.


Hide 3.INSTALL STARTER ARMATURE ASSEMBLY

NOTICE:

Do not drop the starter armature.


a.
A196357
1.531,1.865 1.313,1.635 1.313,1.635 0.927,1.635 true 1.604,0.75 1.229,0.75 false 1.604,0.271 1.229,0.271 false 0.729,1.563 0.958,1.719 0.229,0.156 10 false *3 1.021,0.688 1.323,0.833 0.302,0.146 10 false *2 1.021,0.198 1.292,0.354 0.271,0.156 10 false *1
*1 Snap Ring
*2 Plate Washer
*3 Bearing
V100135

High-temperature Grease


Apply high-temperature grease to the plate washer, a new snap ring, and the bearing.


b.

Mount the starter commutator end frame in a vise between aluminum plates.

NOTICE:

Do not damage the starter commutator end frame.



c.
A196360
1.104,1.188 1.198,1.313 0.094,0.125 6 false .
V100135

High-temperature Grease


Apply high-temperature grease to the starter armature.


d.

Install the starter armature to the starter commutator end frame.


e.

Install the plate washer to the starter armature shaft.


f.
A073993

Using snap ring pliers, install the snap ring.

NOTICE:
·

Be sure to install the snap ring in the armature shaft groove securely.

·

Be sure to properly install the snap ring because it easily expands.




g.

Check the snap ring length.

i.
A058810
1.542,0.219 1.74,0.406 0.198,0.188 10 false *1
*1 Length


Using a vernier caliper, measure the snap ring length.

Maximum length:

5.0 mm (0.197 in.)


If the length is more than the maximum, replace the snap ring.



Hide 4.INSTALL STARTER COMMUTATOR END FRAME COVER

a.
A084616

Install the starter commutator end frame cover to the starter commutator end frame.


Hide 5.INSTALL STARTER ARMATURE PLATE

a.
A073991
2.281,0.438 2.156,0.438 2.156,0.438 1.823,0.823 true 0.333,1.156 0.031,0.323 0.031,0.323 0.219,0.323 false 0.24,0.25 0.448,0.427 0.208,0.177 10 false *2 2.313,0.365 2.521,0.521 0.208,0.156 10 false *1
*1 key
*2 Keyway


Align the keyway of the starter armature plate with the key inside the starter yoke, and install the starter armature plate.


Hide 6.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A079727
2.01,0.521 1.719,0.198 1.719,0.198 1.333,0.198 false 1.563,0.771 1.042,0.552 1.042,0.552 0.885,0.552 true 0.688,0.469 0.875,0.635 0.188,0.167 10 false *2 1.083,0.083 1.271,0.26 0.188,0.177 10 false *1
*1 Rubber Part
*2 Cutout


Align the rubber part on the starter commutator end frame with the cutout of the starter yoke.


b.

Install the starter commutator end frame to the starter yoke.

NOTICE:

The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed, causing the magnet to break.



Hide 7.INSTALL STARTER YOKE ASSEMBLY

a.
A196821
1.604,1.5 1.958,1.5 true 1.448,1.479 2.094,0.729 2.094,0.729 2.198,0.729 true 2.021,1.406 2.281,1.573 0.26,0.167 10 false *2 2.26,0.615 2.51,0.781 0.25,0.167 10 false *1
*1 Groove
*2 Claw


Align the claw of the starter yoke with the groove inside the starter drive housing.


b.

Install the starter yoke with the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 8.INSTALL REPAIR SERVICE STARTER KIT

a.
A196358
2.104,0.958 2.198,1.083 0.094,0.125 6 false .
V100135

High-temperature Grease


Apply high-temperature grease to the plunger and hook.


b.

Hang the plunger hook of the repair service starter kit on the drive lever set pin.


c.
A082694

Install the plunger and return spring.


d.

Install the repair service starter kit with the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)