Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION WIRE
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052453 TRANSMISSION WIRE A

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When working with FIPG material, perform the following:

·

Using a razor blade and gasket scraper, remove all old FIPG material from the gasket surfaces.

·

Clean all components thoroughly to remove all foreign matter.

·

Clean both sealing surfaces with a non-residue solvent.

·

Apply FIPG material in a continuous line approximately 2 to 3 mm (0.0787 to 0.118 in.) in diameter on the sealing surface.

·

Reassemble parts within 10 minutes of applying FIPG material. Failing to do so will require the FIPG material to be removed and reapplied.



PROCEDURE

Hide 1.INSTALL TRANSMISSION WIRE

a.

Coat a new O-ring with ATF, and install it to the transmission wire.


b.

Install the transmission wire to the case, and install the stopper plate with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the 4 connectors to the 4 shift solenoid valves.


Hide 2.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C283392

Install 3 new gaskets.


b.
C282169
2.844,1.885 3,2.083 0.156,0.198 10 false A 3.083,0.563 3.24,0.76 0.156,0.198 10 false A 2.031,0.333 2.188,0.531 0.156,0.198 10 false B 1.313,0.26 1.469,0.458 0.156,0.198 10 false C

Install the oil strainer with the 4 bolts.

Torque:
10 N*m (110 kgf*cm, 8 ft.*lbf)

HINT:

Bolt length:

14 mm (0.55 in.) for A

20 mm (0.79 in.) for B

23 mm (0.91 in.) for C



Hide 3.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C237878
1.729,0.938 1.729,1.792 1.729,1.792 2.031,1.792 true 1.74,1.781 2.323,0.938 true 1.719,1.792 1.229,0.719 true 2.063,1.677 2.406,1.885 0.344,0.208 10 false *1
*1 Magnet


HINT:

Remove any packing material and be careful not to spill oil on the contacting surfaces of the transmission case and oil pan.


a.

Install the 3 magnets to the locations indicated in the illustration.


b.

Apply FIPG to the oil pan as shown in the illustration.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



c.

Install the oil pan with the 19 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 4.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.

Coat a new O-ring with ATF, and install it to the oil filler tube.


b.

Install the oil filler tube with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Install the oil level dipstick.


Hide 5.ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:

Toyota Genuine ATF Type T-IV