1. BEARING POSITION
| Mark | Front Race Diameter
Inside/Outside |
Thrust Bearing Diameter
Inside/Outside |
Rear Race Diameter
Inside/Outside |
|---|---|---|---|
| A | 28.45 mm (1.12 in.)/47.1 to 47.35 mm (1.855 to 1.864 in.) | 29.04 to 29.25 mm (1.144 to 1.151 in.)/50.04 to 50.34 mm (1.971 to 1.981 in.) | - |
| B | 33.0 to 33.25 mm (1.2993 to 1.3090 in.)/49.9 to 50.4 mm (1.97 to 1.98 in.) | 31.45 to 31.70 mm (1.239 to 1.248 in.)/49.1 to 49.4 mm (1.934 to 1.944 in.) | - |
| C | 37.1 to 37.3 mm (1.461 to 1.468 in.)/58.70 to 58.95 mm (2.312 to 2.320 in.) | 33.75 to 33.85 mm (1.329 to 1.332 in.)/49.8 to 50.3 mm (1.97 to 1.98 in.) | - |
| D | 36.5 to 37 mm (1.44 to 1.45 in.)/50.75 to 50.95 mm (1.999 to 2.005 in.) | 33.55 to 33.80 mm (1.321 to 1.330 in.)/47.62 to 47.87 mm (1.875 to 1.884 in.) | - |
| E | 25.98 mm (1.02 in.)/48.87 mm (1.92 in.) | 25.94 to 26.07 mm (1.022 to 1.026 in.)/46.62 to 46.87 mm (1.836 to 1.845 in.) | 26.5 to 27.0 mm (1.05 to 1.06 in.)/47.02 mm (1.85 in.) |
| F | - | 35.0 to 35.3 mm (1.378 to 1.389 in.)/53.50 to 53.75 mm (2.107 to 2.116 in.) | 34.0 to 34.5 mm (1.34 to 1.35 in.)/48.5 to 49.0 mm (1.91 to 1.92 in.) |
| G | 33.55 to 33.80 mm (1.321 to 1.330 in.)/47.3 to 47.8 mm (1.87 to 1.88 in.) | 35.45 to 35.61 mm (1.396 to 1.401 in.)/47.62 to 47.87 mm (1.875 to 1.884 in.) | - |
| H | 28.5 mm (1.12 in.)/44.2 mm (1.74 in.) | 27.65 to 27.8 mm (1.089 to 1.094 in.)/44.2 mm (1.74 in.) | - |
| I | - | 39.38 mm (1.55 in.)/57.94 to 58.24 mm (2.282 to 2.292 in.) | - |
2.SECURE TRANSMISSION CASE
Secure the transmission case to an overhaul attachment.
3.INSTALL NO. 1 FIRST AND REVERSE BRAKE PISTON
| *1 | No. 1 First and Reverse Brake Piston |
| *2 | Reaction Sleeve |
Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.
Coat a new O-ring with ATF and install it to the reaction sleeve.
Install the No. 1 brake piston to the reaction sleeve.
| *1 | No. 1 First and Reverse Brake Piston |
| *2 | Reaction Sleeve |
With the No. 1 brake piston on the bottom (the rear side), install the brake reaction sleeve and No. 1 brake piston to the transmission case.
Be careful not to damage the O-rings.
4.INSTALL NO. 2 FIRST AND REVERSE BRAKE PISTON
Coat a new O-ring with ATF and install it to the brake piston.
| *1 | No. 2 First and Reverse Brake Piston |
With the spring seat of the piston facing upward (the front side), install the piston to the transmission case.
Be careful not to damage the O-ring.
5.INSTALL FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Install the brake return spring to the brake piston.
| *1 | Snap Ring |
| *2 | Brake Return Spring Claw |
Place SST on the brake return spring and compress the brake return spring.
Using SST, install the snap ring. Make sure the end gap of the snap ring is not aligned with a brake return spring claw.
6.INSPECT PISTON OPERATION OF FIRST AND REVERSE BRAKE
Make sure the first and reverse brake pistons move smoothly when compressed air is applied into the transmission case.
7.INSTALL LEAF SPRING
8.INSTALL NO. 2 1-WAY CLUTCH
Coat the No. 2 planetary carrier thrust washer with petroleum jelly.
Install the thrust washer to the planetary gear.
Make sure that the tabs of the washer fit into the cutout portions of the planetary gear.
| *1 | Open End |
| *2 | Guide |
Install the 1-way clutch to the planetary gear.
Make sure that the open ends of the guides of the 1-way clutch are facing upward.
Using a screwdriver, install the snap ring.
Be careful not to damage the rear planetary gear.
Tape the screwdriver tip before use.
While turning the 1-way clutch inner race counterclockwise, install the 1-way clutch inner race to the planetary gear.
9.INSPECT NO. 2 1-WAY CLUTCH
10.INSTALL REAR PLANETARY GEAR ASSEMBLY
Install the ring gear flange to the rear planetary ring gear.
Using a screwdriver, install the snap ring.
Be careful not to damage the rear planetary ring gear.
Tape the screwdriver tip before use.
| *1 | Bearing H |
| *2 | Bearing Race H |
Coat the bearing and bearing race with petroleum jelly and install them to the rear planetary ring gear.
| Item | Inside | Outside |
|---|---|---|
| Bearing H | 27.65 to 27.8 mm (1.089 to 1.094 in.) | 44.2 mm (1.74 in.) |
| Bearing Race H | 28.5 mm (1.12 in.) | 44.2 mm (1.74 in.) |
Coat the No. 1 planetary carrier thrust washer with petroleum jelly.
Install the thrust washer to the planetary gear.
Make sure that the tabs of the washer fit into the cutout portions of the planetary gear.
Install the rear planetary gear to the rear planetary ring gear.
11.INSTALL PLANETARY OUTPUT SHAFT OIL SEAL RING
Coat a new oil seal ring with ATF and install it to the output shaft.
After installing the oil seal ring, check that it rotates smoothly.
Do not expand the ring excessively.
12.INSTALL OUTPUT SHAFT
Install the output shaft to the rear planetary gear flange.
13.INSTALL SECOND BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the second brake piston.
While being careful not to damage the O-rings, press the second brake piston toward the second brake drum with both hands.
14.INSTALL SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
Install the piston return spring.
Install the second brake piston return spring seat.
Place SST on the spring retainer, compress the return spring with a press, and then install the snap ring.
Do not deform the spring seat. Stop compressing the spring when the spring seat is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.
15.INSPECT SECOND BRAKE PISTON
16.INSTALL NO. 4 PLANETARY CARRIER THRUST WASHER
Coat the thrust washer with petroleum jelly and install it.
Make sure that the cutout portions of the thrust washer fit onto the teeth of the spring seat.
17.INSTALL FIRST AND REVERSE BRAKE DISC SET
| *1 | Flange |
| *2 | Disc |
| *3 | Plate |
Install the flange with the rounded edge facing upward.
Install the 7 discs and 7 plates.
*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3
18.INSTALL OUTPUT SHAFT WITH REAR PLANETARY GEAR, NO. 2 1-WAY CLUTCH, FIRST AND REVERSE BRAKE DISC SET AND SECOND BRAKE DRUM
Coat the bearing with petroleum jelly and install it to the case.
| Item | Inside | Outside |
|---|---|---|
| Bearing I | 39.38 mm (1.55 in.) | 57.94 to 58.24 mm (2.282 to 2.292 in.) |
Make sure the bearing is installed facing the proper direction.
Align the teeth on the flange, discs and plates.
Install the second brake drum to the planetary gear with the snap ring facing upward.
Make sure the oil hole in the drum faces towards the lower side of the transmission case (the side where the valve body is installed).
Align the teeth of the planetary gear assembly, indicated by A in the illustration, with the splines of the transmission case, indicated by B in the illustration.
Install the assembled planetary gear.
| *1 | Wooden Block |
Place the output shaft on wooden blocks.
Using SST, install the snap ring.
19.SELECT FIRST AND REVERSE BRAKE FLANGE
Using a feeler gauge, measure the clearance between the plate and second brake drum.
0.70 to 1.22 mm (0.0276 to 0.0480 in.)
If the clearance is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.
| Mark | Thickness |
|---|---|
| 55 | 3.94 to 4.06 mm (0.156 to 0.159 in.) |
| 54 | 4.14 to 4.26 mm (0.163 to 0.167 in.) |
| 53 | 4.34 to 4.46 mm (0.171 to 0.175 in.) |
| 52 | 4.54 to 4.66 mm (0.179 to 0.183 in.) |
| 51 | 4.74 to 4.86 mm (0.187 to 0.191 in.) |
| 50 | 4.92 to 5.08 mm (0.194 to 0.199 in.) |
| 66 | 5.10 to 5.30 mm (0.201 to 0.208 in.) |
| 67 | 5.30 to 5.50 mm (0.209 to 0.216 in.) |
20.INSTALL SECOND BRAKE PISTON SLEEVE
21.INSTALL BRAKE DRUM GASKET
Coat a new gasket with ATF and install it.
22.INSTALL NO. 1 1-WAY CLUTCH ASSEMBLY
Install the 1-way clutch as shown in the illustration.
23.INSTALL SECOND BRAKE DISC SET
| *1 | Plate (A) |
| *2 | Disc |
| *3 | Plate (B) |
| *4 | Flange |
Install the plate (A) with the rounded edge of the plate facing the discs.
| Item | Specified Condition |
|---|---|
| Plate (A) | 1.8 mm (0.0709 in.) |
| Plate (B) | 2.5 mm (0.0984 in.) |
Install the 5 discs, 4 2.5 mm (0.0984 in.) thick plates and flange.
*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *4
Using a screwdriver, install the snap ring.
Be careful not to damage the transmission case.
Tape the screwdriver tip before use.
24.INSPECT SECOND BRAKE
Using a feeler gauge, measure the clearance between the snap ring and flange.
0.62 to 1.98 mm (0.0245 to 0.0779 in.)
If the clearance is not as specified, inspect the discs.
25.INSTALL SUN GEAR INPUT DRUM SHAFT SNAP RING
Be careful not to damage the planetary sun gear.
Tape the screwdriver tip before use.
Using a screwdriver, install the snap ring to the planetary sun gear.
26.INSTALL SUN GEAR INPUT DRUM
Place the planetary sun gear onto a wooden block or similar object.
Install the input drum to the planetary sun gear.
Using snap ring pliers, install the snap ring.
27.INSTALL SUN GEAR SHAFT OIL SEAL RING
Coat the 2 oil seal rings with ATF install the 2 oil seal rings to the planetary sun gear.
After installing the oil seal rings, check that they rotate smoothly.
Do not expand the rings excessively.
28.INSTALL NO. 1 1-WAY CLUTCH THRUST WASHER
Make sure that the tabs of the washer fit into the holes in the sun gear input drum.
29.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY WITH SUN GEAR INPUT DRUM
While turning the sun gear clockwise, install it to the 1-way clutch.
Confirm that the thrust washer is installed correctly.
30.INSTALL FRONT PLANETARY GEAR ASSEMBLY
| *1 | Bearing Race G |
| *2 | Bearing G |
Coat the bearing and bearing race with petroleum jelly and install them to the planetary gear.
| Item | Inside | Outside |
|---|---|---|
| Bearing Race G | 33.55 to 33.80 mm (1.321 to 1.330 in.) | 47.3 to 47.8 mm (1.87 to 1.88 in.) |
| Bearing G | 35.45 to 35.61 mm (1.396 to 1.401 in.) | 47.62 to 47.87 mm (1.875 to 1.884 in.) |
Make sure the bearing and race are installed facing the proper directions.
Install the planetary gear to the sun gear input drum.
Using SST, install the snap ring.
Remove the wooden blocks from under the output shaft.
Coat the bearing race with petroleum jelly and install it to the planetary gear.
| Item | Inside | Outside |
|---|---|---|
| Bearing Race F | 34.0 to 34.5 mm (1.34 to 1.35 in.) | 48.5 to 49.0 mm (1.91 to 1.92 in.) |
Make sure the bearing race is installed facing the proper direction.
31.INSTALL SECOND COAST BRAKE BAND ASSEMBLY
Install the brake band to the case.
Install the pin to the brake band as shown in the illustration.
Install the E-ring to the pin.
32.INSTALL INPUT SHAFT OIL SEAL RING
Coat the 3 new oil seal rings with ATF.
Squeeze the ends of the 3 new oil seal rings together, and then install them to the input shaft groove.
Do not squeeze the rings excessively.
After installing the oil seal rings, check that they rotate smoothly.
33.INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY
Coat 2 new O-rings with ATF and install them to the forward clutch piston.
Coat a new O-ring with ATF and install it to the input shaft.
Press the clutch piston into the input shaft with both hands to install it.
Be careful not to damage the O-ring.
34.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY
Install the piston return spring.
Place SST on the return spring, compress the return spring with a press, and then install the snap ring.
Make sure the end gap of the snap ring is not aligned with the return spring claw.
35.INSTALL FORWARD CLUTCH DISC SET
Install the cushion plate.
| *1 | Plate |
| *2 | Disc |
| *3 | Flange |
Install the 6 plates, 6 discs and flange.
*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3
| *1 | Protective Tape |
Using a screwdriver, install the snap ring.
Make sure the end gap of the snap ring is not aligned with the cutout portion of the input shaft.
Be careful not to damage the input shaft.
Tape the screwdriver tip before use.
36.SELECT FORWARD CLUTCH FLANGE
Using SST and a dial indicator, measure the piston stroke (A) of the clutch flange at both ends across the diameter while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi))
0.60 to 1.00 mm (0.0236 to 0.0393 in.)
If the piston stroke (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.
| Mark | Thickness |
|---|---|
| 90 | 2.95 to 3.05 mm (0.117 to 0.120 in.) |
| 91 | 3.15 to 3.25 mm (0.125 to 0.127 in.) |
| 92 | 3.35 to 3.45 mm (0.132 to 0.135 in.) |
| 93 | 3.55 to 3.65 mm (0.140 to 0.143 in.) |
| 94 | 3.75 to 3.85 mm (0.148 to 0.151 in.) |
| 95 | 3.95 to 4.05 mm (0.156 to 0.159 in.) |
| 96 | 4.15 to 4.25 mm (0.164 to 0.167 in.) |
| 97 | 4.35 to 4.45 mm (0.172 to 0.175 in.) |
37.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY
| *1 | O-Ring |
Coat 2 new O-rings with ATF and install them to the direct clutch piston.
Press the clutch piston into the clutch drum with both hands to install it.
Be careful not to damage the O-rings.
38.INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY
Install the piston return spring.
Place SST on the spring retainer, compress the return spring with a press, and then install the snap ring.
Be sure the end gap of the snap ring is not aligned with the return spring claw.
39.INSTALL DIRECT CLUTCH DISC SET
| *1 | Plate |
| *2 | Disc |
| *3 | Flange |
Install the 4 plates and 4 discs.
Install the flange with the flat end facing downward.
*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3
| *1 | Protective Tape |
Using a screwdriver, install the snap ring.
Make sure the end gap of the snap ring is not aligned with the cutout portion of the direct clutch drum.
Be careful not to damage the direct clutch drum.
Tape the screwdriver tip before use.
40.SELECT DIRECT CLUTCH FLANGE
Place the direct clutch onto the overdrive support.
Using SST and a dial indicator, measure the piston stroke (A) of the clutch flange at both ends across the diameter while applying and releasing compressed air (186 to 206 kPa (1.9 to 2.1 kgf/cm2, 27 to 30 psi)).
0.40 to 0.70 mm (0.0158 to 0.0275 in.)
If the piston stroke (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.
| Mark | Thickness |
|---|---|
| 53 | 3.25 to 3.35 mm (0.128 to 0.131 in.) |
| 54 | 3.35 to 3.45 mm (0.132 to 0.135 in.) |
| 55 | 3.45 to 3.55 mm (0.136 to 0.139 in.) |
| 56 | 3.55 to 3.65 mm (0.140 to 0.143 in.) |
| 57 | 3.65 to 3.75 mm (0.144 to 0.147 in.) |
| 58 | 3.75 to 3.85 mm (0.148 to 0.151 in.) |
41.INSTALL DIRECT CLUTCH ASSEMBLY
| *1 | Thrust Washer |
Install the thrust washer to the input shaft.
Install the direct clutch to the input shaft.
42.INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY
| *1 | Bearing Race E |
| *2 | Bearing E |
Coat the bearing race and bearing with petroleum jelly and install them to the input shaft.
| Item | Inside | Outside |
|---|---|---|
| Bearing Race E | 25.98 mm (1.02 in.) | 48.87 mm (1.92 in.) |
| Bearing E | 25.94 to 26.07 mm (1.022 to 1.026 in.) | 46.62 to 46.87 mm (1.836 to 1.845 in.) |
Make sure the bearing and race are installed facing the proper directions.
| *1 | Bearing Race E |
Coat the bearing race with petroleum jelly and install it to the front planetary ring gear.
| Item | Inside | Outside |
|---|---|---|
| Bearing Race E | 26.5 to 27.0 mm (1.05 to 1.06 in.) | 47.02 mm (1.85 in.) |
Make sure the bearing race is installed facing the proper direction.
Align the teeth of the discs in the forward clutch.
Align the splines of the planetary ring gear with the teeth of the discs and install the planetary ring gear to the forward clutch.
43.INSTALL DIRECT CLUTCH ASSEMBLY WITH FORWARD CLUTCH ASSEMBLY
| *1 | Bearing F |
Coat the bearing with petroleum jelly and install it to the ring gear.
| Item | Inside | Outside |
|---|---|---|
| Bearing F | 35.0 to 35.3 mm (1.378 to 1.389 in.) | 53.50 to 53.75 mm (2.107 to 2.116 in.) |
Make sure the bearing is installed facing the proper direction.
Install the assembled direct clutch, forward clutch and front planetary ring gear to the transmission case.
Using a vernier caliper, measure the distance between the sun gear input drum and direct clutch drum as shown in the illustration.
5.3 to 7.3 mm (0.209 to 0.287 in.)
If the distance is not as specified, check for improper installation.
Coat the bearing with petroleum jelly and install it to the forward clutch.
| Item | Inside | Outside |
|---|---|---|
| Bearing D | 33.55 to 33.80 mm (1.321 to 1.330 in.) | 47.62 to 47.87 mm (1.875 to 1.884 in.) |
Make sure the bearing is installed facing the proper direction.
44.INSTALL SECOND COAST BRAKE PISTON ROD
| *1 | Piston Rod |
| *2 | Washer Plate |
| *3 | Compression Spring |
| *4 | Piston |
Install the washer plate, compression spring and piston to the piston rod.
Firmly press the piston down to compress the compression spring.
Install the E-ring.
45.INSTALL SECOND COAST BRAKE PISTON OIL SEAL RING
Coat a new oil seal ring with ATF.
Spread the ends of the ring to install the oil seal ring to the piston groove. Then squeeze its ends together.
Do not spread the ring ends excessively.
46.INSTALL SECOND COAST BRAKE PISTON ASSEMBLY
Coat 2 new O-rings with ATF and install them to the second coast brake cover.
Install the spring, piston assembly and cover to the case.
Using SST, install the snap ring.
47.INSPECT PISTON STROKE OF SECOND COAST BRAKE
| *1 | Piston Rod |
| *2 | Mark |
Using a waterproof pen, place a mark on the second coast brake piston rod as shown in the illustration.
Using SST, measure the piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
1.5 to 3.0 mm (0.0591 to 0.118 in.)
If the piston stroke is not as specified, inspect the brake band.
If the piston stroke is still not as specified, select a piston rod of an appropriate length from the table below so that the measured value is within the standard range.
| Groove Mark | Length |
|---|---|
| Without | 78.3 to 78.5 mm (3.083 to 3.090 in.) |
| With | 79.8 to 80.0 mm (3.142 to 3.149 in.) |
48.INSTALL OVERDRIVE BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the overdrive brake piston.
Press the brake piston into the overdrive support with both hands to install it.
Be careful not to damage the O-rings.
49.INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY
Install the return spring to the brake piston.
| *1 | Protective Tape |
Place SST on the return spring and compress the return spring with a press.
Using a screwdriver, install the snap ring.
Make sure the end gap of the snap ring is not aligned with the cutout portion of the overdrive support.
Be careful not to damage the overdrive support sub-assembly and return spring.
After assembling the overdrive support assembly completely, align the position of the piston with A in the illustration.
Align the end gap of the snap ring with B in the illustration.
Make sure that the snap ring is not on top of the part of the return spring that prevents the snap ring from coming off. Check this in all 8 locations.
Tape the screwdriver tip before use.
50.INSPECT PISTON OPERATION OF OVERDRIVE BRAKE
51.INSTALL OVERDRIVE CLUTCH DRUM OIL SEAL RING
Coat 2 new oil seal rings with ATF.
Squeeze the ends of the 2 oil seal rings together, and then install them to the stator shaft groove.
Do not squeeze the rings excessively.
After installing the oil seal rings, check that they rotate smoothly.
52.INSTALL OVERDRIVE BRAKE ASSEMBLY
| *1 | Bearing C |
| *2 | Bearing Race D |
Coat the bearing and bearing race with petroleum jelly and install them to the overdrive brake assembly.
| Item | Inside | Outside |
|---|---|---|
| Bearing C | 33.75 to 33.85 mm (1.329 to 1.332 in.) | 49.8 to 50.3 mm (1.97 to 1.98 in.) |
| Bearing Race D | 36.5 to 37 mm (1.44 to 1.45 in.) | 50.75 to 50.95 mm (1.9996 to 2.005 in.) |
Make sure the bearing and race are installed facing the proper directions.
Coat the thrust washer with petroleum jelly and install it to the overdrive support.
Make sure that the tab of the washer fits into the groove of the overdrive support.
Using the 2 bolts of SST, aim the bolt and oil holes of the overdrive brake assembly toward the valve body side, and align them with the bolt holes of the transmission case. Then install the overdrive brake assembly.
Temporarily install the 2 bolts.
Using SST, install the snap ring.
24 mm (0.945 in.)
Install the snap ring with the open end facing toward the valve body.
Tighten the 2 bolts.
53.INSPECT OUTPUT SHAFT END PLAY
54.INSTALL OVERDRIVE BRAKE DISC SET
| *1 | Plate |
| *2 | Disc |
| *3 | Flange |
Install the 4 plates, 4 discs and flange.
*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3
| *1 | Protective Tape |
Using a screwdriver, install the snap ring.
Be careful not to damage the transmission case.
Tape the screwdriver tip before use.
55.SELECT OVERDRIVE BRAKE FLANGE
Place SST and a dial indicator on the overdrive brake piston.
Measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi))
1.75 to 2.05 mm (0.0689 to 0.0807 in.)
If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.
If the piston stroke is still outside the standard range, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.
| Mark | Thickness |
|---|---|
| 33 | 3.25 to 3.35 mm (0.128 to 0.131 in.) |
| 35 | 3.45 to 3.55 mm (0.136 to 0.139 in.) |
| 36 | 3.55 to 3.65 mm (0.140 to 0.143 in.) |
| 37 | 3.65 to 3.75 mm (0.144 to 0.147 in.) |
| 38 | 3.75 to 3.85 mm (0.148 to 0.151 in.) |
| 39 | 3.85 to 3.95 mm (0.152 to 0.155 in.) |
| 40 | 3.95 to 4.05 mm (0.156 to 0.159 in.) |
56.INSTALL OVERDRIVE PLANETARY RING GEAR FLANGE
Install the ring gear flange to the overdrive planetary ring gear.
Using a screwdriver, install the snap ring.
Be careful not to damage the overdrive planetary ring gear and the flange.
Tape the screwdriver tip before use.
57.INSTALL OVERDRIVE PLANETARY RING GEAR
| *1 | Bearing Race C |
Coat the bearing race with petroleum jelly and install it to the overdrive planetary ring gear flange.
| Item | Inside | Outside |
|---|---|---|
| Bearing Race C | 37.1 to 37.3 mm (1.461 to 1.468 in.) | 58.70 to 58.95 mm (2.312 to 2.320 in.) |
Make sure the bearing race is installed facing the proper direction.
Install the ring gear.
58.INSTALL NO. 3 OVERDRIVE PLANETARY GEAR THRUST WASHER
Install the thrust washer to the overdrive planetary gear with the grooves facing upward.
59.INSTALL OVERDRIVE 1-WAY CLUTCH
| *1 | Flange |
Install the 2 retainers to the 1-way clutch.
Install the 1-way clutch to the outer race with the flange of the 1-way clutch facing upward.
Install the overdrive 1-way clutch and outer race to the overdrive planetary gear.
60.INSTALL OVERDRIVE RETAINING PLATE
Install the retaining plate.
Using a screwdriver, install the snap ring.
Be careful not to damage the overdrive planetary gear assembly and the plate.
Tape the screwdriver tip before use.
61.INSPECT OVERDRIVE 1-WAY CLUTCH
62.INSTALL OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY
Coat 2 new O-rings with ATF and install them to the overdrive direct clutch piston.
Press the clutch piston into the clutch drum with both hands to install it.
Be careful not to damage the O-rings.
63.INSTALL OVERDRIVE DIRECT RETURN SPRING SUB-ASSEMBLY
Install the overdrive brake return spring to the overdrive direct clutch piston.
| *1 | Return Spring Claw |
Place SST on the spring retainer, compress the return spring with a press, and then install the snap ring.
Make sure the end gap of the snap ring is not aligned with the return spring claw.
64.INSTALL OVERDRIVE DIRECT CLUTCH DISC SET
| *1 | Plate |
| *2 | Disc |
Install the 2 plates and 2 discs.
*1 - *2 - *1 - *2
Install the flange with the flat end facing downward.
Using a screwdriver, install the snap ring.
Be careful not to damage the overdrive direct.
Tape the screwdriver tip before use.
65.SELECT OVERDRIVE DIRECT CLUTCH FLANGE
Place the oil pump onto the torque converter assembly, and then place the overdrive direct clutch drum assembly onto the oil pump.
| *1 | Vinyl Tape |
Using SST and a dial indicator, measure the overdrive direct clutch piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
1.85 to 2.15 mm (0.0729 to 0.0846 in.)
If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.
If the piston stroke is still outside the standard range, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.
| Mark | Thickness |
|---|---|
| 21 | 3.05 to 3.15 mm (0.121 to 0.124 in.) |
| 20 | 3.15 to 3.25 mm (0.125 to 0.127 in.) |
| 19 | 3.25 to 3.35 mm (0.128 to 0.131 in.) |
| 18 | 3.35 to 3.45 mm (0.132 to 0.135 in.) |
| 17 | 3.45 to 3.55 mm (0.136 to 0.139 in.) |
| 16 | 3.55 to 3.65 mm (0.140 to 0.143 in.) |
66.INSTALL OVERDRIVE DIRECT CLUTCH DRUM
Align the teeth of the discs in the direct clutch assembly.
Install the direct clutch drum assembly to the overdrive planetary gear.
67.INSTALL OVERDRIVE PLANETARY GEAR ASSEMBLY WITH DIRECT CLUTCH ASSEMBLY AND OVERDRIVE 1-WAY CLUTCH ASSEMBLY
| *1 | Bearing B |
Coat the bearing with petroleum jelly and install it to the ring gear.
| Item | Inside | Outside |
|---|---|---|
| Bearing B | 31.45 to 31.70 mm (1.239 to 1.248 in.) | 49.1 to 49.4 mm (1.934 to 1.944 in.) |
Make sure the bearing is installed facing the proper direction.
| *1 | Bearing Race B |
Coat the bearing race with petroleum jelly and install it to the planetary gear.
| Item | Inside | Outside |
|---|---|---|
| Bearing Race B | 33.0 to 33.25 mm (1.2993 to 1.3090 in.) | 49.9 to 50.4 mm (1.97 to 1.98 in.) |
Make sure the bearing race is installed facing the proper direction.
Install the overdrive planetary gear together with the overdrive direct clutch and 1-way clutch.
Place SST on the transmission case.
Using a vernier caliper, measure the distance between the top of SST and the clutch drum.
15.5 to 16.5 mm (0.611 to 0.649 in.)
If the distance is not as specified, check for improper installation.
| *1 | Bearing A |
Coat the bearing with petroleum jelly and install it to the overdrive direct clutch.
| Item | Inside | Outside |
|---|---|---|
| Bearing A | 29.04 to 29.25 mm (1.144 to 1.151 in.) | 50.04 to 50.34 mm (1.971 to 1.981 in.) |
Make sure the bearing is installed facing the proper direction.
68.INSTALL OIL PUMP ASSEMBLY
| *1 | Bearing Race A |
Coat the bearing race with petroleum jelly and install it to the oil pump.
| Item | Inside | Outside |
|---|---|---|
| Bearing Race A | 28.45 mm (1.12 in.) | 47.1 to 47.35 mm (1.855 to 1.864 in.) |
Make sure the bearing race is installed facing the proper direction.
Coat a new O-ring with ATF and install it to the pump body.
Slide the oil pump onto the input shaft, align the bolt holes of the oil pump assembly with the bolt holes of the transmission case and install the oil pump.
Hold the input shaft and lightly press the oil pump body to slide the oil seal rings toward the overdrive direct clutch drum.
Do not forcefully push on the oil pump as the oil seal rings will stick to the direct clutch drum.
Install the 7 bolts.
69.INSPECT INPUT SHAFT ROTATION
Make sure the input shaft rotates smoothly.
70.INSPECT INDIVIDUAL PISTON OPERATION
| *1 | Overdrive Direct Clutch (C1) |
| *2 | Direct Clutch (C2) |
| *3 | Forward Clutch (C3) |
| *4 | Overdrive Brake (B1) |
| *5 | Second Coast Brake (B2) |
| *6 | Second Brake (B3) |
| *7 | First and Reverse Brake (B4) |
| *8 | C-0 Accumulator Piston Hole |
Check the operating sound while applying compressed air to the oil hole indicated in the illustration.
When inspecting the overdrive direct clutch, check the operating sound with the C-0 accumulator piston hole closed.
If there is no sound, disassemble and check the installation condition of the parts.
71.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL
Using SST and a hammer, tap in 2 new oil seals.
Coat the lips of the oil seals with MP grease.
72.INSTALL MANUAL VALVE LEVER SHAFT
| *1 | Spacer |
| *2 | Manual Valve Lever Shaft |
| *3 | Manual Valve Lever |
Install a new spacer to the manual valve lever.
Pass the manual valve lever shaft through the transmission case and manual valve lever to install it.
Using a hammer, tap in a new spring pin.
Align the manual valve lever indentation with the spacer hole and stake them with a punch.
Check that the shaft rotates smoothly.
73.INSTALL PARKING LOCK PAWL
| *1 | E-Ring |
| *2 | Parking Lock Pawl Shaft |
| *3 | Parking Lock Pawl |
| *4 | Spring |
Install the E-ring to the parking lock pawl shaft.
Install the parking lock pawl, shaft and spring.
74.INSTALL PARKING LOCK ROD SUB-ASSEMBLY
Connect the parking lock rod to the manual valve lever to install it.
75.INSTALL PARKING LOCK PAWL BRACKET
Install the parking lock pawl bracket to the transmission case with the 3 bolts.
| *1 | Manual Valve Lever |
| *2 | Planetary Ring Gear |
| *3 | Parking Lock Pawl |
Shift the manual valve lever to the P position and confirm that the planetary ring gear is correctly locked by the parking lock pawl.
76.INSTALL C-0 ACCUMULATOR PISTON
Coat a new O-ring with ATF and install it to the piston.
Install the 2 springs and accumulator piston to the hole.
| Item | Free Length
Outer Diameter |
Color |
|---|---|---|
| C-0 Inner Spring | 46.0 mm (1.81 in.)
14.02 mm (0.552 in.) |
Yellow |
| C-0 Outer Spring | 74.6 mm (2.94 in.)
20.9 mm (0.823 in.) |
Orange |
77.INSTALL B-0 ACCUMULATOR PISTON
Coat 2 new O-rings with ATF and install them to the piston.
Install the spring and accumulator piston to the hole.
| Item | Free Length
Outer Diameter |
Color |
|---|---|---|
| B-0 Spring | 63.6 mm (2.50 in.)
16.0 mm (0.630 in.) |
Red |
78.INSTALL C-2 ACCUMULATOR PISTON
Coat 2 new O-rings with ATF and install them to the piston.
Install the 2 springs and accumulator piston to the hole.
| Item | Free Length
Outer Diameter |
Color |
|---|---|---|
| C-2 Inner Spring | 42.06 mm (1.66 in.)
14.7 mm (0.579 in.) |
Pink |
| C-2 Outer Spring | 68.53 mm (2.70 in.)
20.2 mm (0.795 in.) |
Blue |
79.INSTALL B-2 ACCUMULATOR PISTON
Coat 2 new O-rings with ATF and install them to the piston.
Install the spring and accumulator piston to the hole.
| Item | Free Length
Outer Diameter |
Color |
|---|---|---|
| B-2 Spring | 70.50 mm (2.78 in.)
19.9 mm (0.783 in.) |
Red |
80.INSTALL CHECK BALL BODY
| *1 | Spring |
| *2 | Check Ball Body |
Install the spring and check ball body.
81.INSTALL TRANSMISSION VALVE BODY ASSEMBLY
| *1 | Manual Valve |
| *2 | Pin |
| *3 | Manual Valve Lever |
Install the valve body and align the groove of the manual valve with the pin of the manual valve lever.
Install the 20 bolts.
Each bolt length is indicated below.
23 mm (0.906 in.) for A
28 mm (1.10 in.) for B
36 mm (1.42 in.) for C
82.INSTALL TRANSMISSION WIRE
Coat a new O-ring with ATF and install it to the transmission wire.
Install the transmission wire to the case.
Install the stopper plate with the bolt.
Connect the 4 connectors to the 4 shift solenoid valves.
83.INSTALL VALVE BODY OIL STRAINER ASSEMBLY
Install 3 new gaskets to the oil strainer.
Install the oil strainer with the 4 bolts.
Each bolt length is indicated below.
14 mm (0.55 in.) for A
20 mm (0.79 in.) for B
23 mm (0.91 in.) for C
84.INSTALL OIL CLEANER MAGNET
| *1 | Magnet |
Install the 3 magnets.
85.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
Remove all old seal packing from the contact surfaces of the transmission case and oil pan.
Be careful not to drop oil on the contact surfaces of the transmission case and oil pan.
Apply seal packing to the oil pan.
Toyota Genuine Seal Packing 1281,
Three Bond 1281 or equivalent
2 to 3 mm (0.0788 to 0.118 in.)
Install the oil pan with the 19 bolts.
86.INSTALL SENSOR ROTOR
| *1 | Key |
| *2 | Sensor Rotor |
Using a snap ring expander, install the snap ring.
Install the key and sensor rotor.
87.INSTALL TRANSFER CASE ADAPTER REAR OIL SEAL
Coat the lip of a new oil seal with MP grease.
Using SST and a hammer, tap in the oil seal.
0 to 1 mm (0 to 0.0394 in.)
Be careful not to damage the lip of the oil seal.
88.INSTALL TRANSFER CASE REAR ADAPTER OIL RECEIVER
Install the transfer case rear adaptor oil receiver to the rear transfer adaptor.
Using snap ring expander, install the snap ring.
89.INSTALL REAR TRANSFER ADAPTER
Clean the threads of the bolts and case with non-residue solvent.
| *1 | Seal Packing |
Apply seal packing to the rear adaptor transfer.
Toyota Genuine Seal Packing 1281,
Three Bond 1281 or equivalent
1.0 to 1.5 mm (0.0394 to 0.0591 in.)
Install the rear adaptor transfer with the 8 bolts.
Each bolt length is indicated below.
50 mm (1.97 in.) for A
40 mm (1.58 in.) for B
90.INSTALL AUTOMATIC TRANSMISSION HOUSING
Clean the threads of the bolts and case with non-residue solvent.
Apply adhesive to the 6 bolts.
Toyota Genuine Adhesive 1324,
Three Bond 1324 or equivalent
Install the transmission housing with the 6 bolts.
91.INSTALL SPEED SENSOR SP2
Coat a new O-ring with ATF and install it to the sensor.
Install the sensor with the bolt.
92.INSTALL SPEED SENSOR NC0
Coat a new O-ring with ATF and install it to the sensor.
Install the speed sensor with the bolt.
93.INSTALL OIL COOLER TUBE UNION
| *a | -2 to 2° |
| *b | 5 to 9° |
Coat 2 new O-rings with ATF and install one to each tube union.
94.INSTALL ATF TEMPERATURE SENSOR
Coat the O-ring with ATF.
Install the sensor.
95.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Install the park/neutral position switch to the manual valve lever shaft and temporarily install the adjusting bolt.
Install a new lock washer and the lock nut.
Turn the control shaft lever LH clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.
| *1 | Neutral Basic Line |
| *2 | Groove |
Align the neutral basic line with the switch groove as shown in the illustration and tighten the adjusting bolt.
Using a screwdriver, bend the tabs of the lock washer.
96.INSTALL TRANSMISSION CONTROL SHAFT LEVER LH
Install the control shaft lever with the washer and nut.
97.INSTALL BREATHER HOSE
Install the breather hose with the bolt.
98.INSTALL DRAIN PLUG
Install a new gasket and the drain plug.