Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER AND DRIVE PLATE
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052460 TORQUE CONVERTER AND DRIVE PLATE G

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 1.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

a.
C283055
1.458,0.813 0.688,0.604 0.688,0.604 1.385,0.667 true 0.365,0.521 0.823,0.719 0.458,0.198 10 false SST

Inspect the one-way clutch.

i.

Set SST into the inner race of the one-way clutch.

SST
09350-32014  (09351-32010)


ii.

Install SST so that it fits in the notch of the torque converter hub and in the outer race of the one-way clutch.

SST
09350-32014  (09351-32020)


iii.
C283056
1.74,1.063 2.354,0.615 2.354,0.615 2.24,0.885 false 2.385,0.427 2.844,0.625 0.458,0.198 10 false SST 1.917,1.677 2.229,1.875 0.313,0.198 10 false *b 1.771,0.292 2.083,0.49 0.313,0.198 10 false *a
*a Hold
*b Turn
V100135

Lock
V100136

Smooth


Stand the torque converter up and turn SST.

OK:

The one-way clutch rotates smoothly when turned clockwise and locks when turned counterclockwise.




b.
C283395
0.135,0.115 0.448,0.271 0.313,0.156 10 false *1
*1 Sample showing maximum allowable amount of powder in ATF


Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or is locked in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).

HINT:

The sample illustration shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF that was removed from a torque converter.




c.

Replace the ATF in the torque converter.

HINT:

If the ATF is discolored or has a foul odor, stir the ATF in the torque converter before replacing the ATF.



d.

Clean and check the oil cooler and oil pipe line.

HINT:
·

If the torque converter is inspected or the ATF is replaced, it is necessary to clean the oil cooler and oil pipe line.

·

Apply compressed air of 196 kPa (2.0 kgf/cm2, 28 psi) into the inlet hose.

·

If a large amount of powder is found in the ATF, add new ATF using a bucket pump and clean the oil cooler and oil pipe line again.

·

If the ATF is cloudy, inspect the oil cooler.




e.
D025368
1.74,1.833 2.219,1.063 true 2.281,0.948 2.635,1.135 0.354,0.188 10 false *c 0.438,0.115 0.708,0.448 0.271,0.333 10 false *a 1.479,0.115 1.75,0.448 0.271,0.333 10 false *b
*a CORRECT
*b INCORRECT
*c Bottom is damage


Prevent deformation of the torque converter and damage to the oil pump gear.

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter or to the bottom of a bolt hole, replace the bolt and torque converter.



Hide 2.INSPECT DRIVE PLATE AND RING GEAR

C283394
0.427,1.75 0.74,1.906 0.313,0.156 10 false *1 1.313,1.031 1.521,1.229 0.208,0.198 10 false 1 1.75,0.302 1.958,0.5 0.208,0.198 10 false 2 2.469,0.406 2.677,0.604 0.208,0.198 10 false 3 2.979,1.188 3.188,1.385 0.208,0.198 10 false 4 2.729,1.896 2.938,2.094 0.208,0.198 10 false 5 1.875,1.875 2.083,2.073 0.208,0.198 10 false 6
*1 Measurement Point


a.

Check the drive plate for damage.


b.

Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter.

Maximum runout:

0.30 mm (0.0118 in.)


HINT:

If the runout is more than the maximum or the drive plate is damage, replace the drive plate (See page Engine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY(w/o Glow Plug Controller)>REMOVAL).