Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM U

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  TERMINALS OF ECU  


CHECK TCM


C214981
1.406,0.333 1.823,0.583 0.417,0.25 3.458,0.333 3.875,0.583 0.417,0.25 5.406,0.333 5.823,0.583 0.417,0.25 1.49,0.375 1.99,0.75 0.5,0.375 10 C24 3.542,0.375 3.969,0.625 0.427,0.25 10 G40 5.49,0.375 6.042,0.708 0.552,0.333 10 G41

HINT:

The standard voltage at each TCM terminal is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the TCM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C24-12 (NSW) - C24-1 (E1) L-Y - BR PNP switch signal
·

Ignition switch ON

·

Shift lever in P or N


Below 1 V
·

Ignition switch ON

·

Shift lever not in P or N


11 to 14 V
G40-9 (R) - C24-1 (E1) R-Y - BR R shift position switch signal
·

Ignition switch ON

·

Shift lever in R


11 to 14 V
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
G40-8 (D) - C24-1 (E1) G-Y - BR D shift position switch signal
·

Ignition switch ON

·

Shift lever in D or 3


11 to 14 V
·

Ignition switch ON

·

Shift lever not in D or 3


Below 1 V
G40-12 (3) - C24-1 (E1) G-O - BR 3 shift position switch signal
·

Ignition switch ON

·

Shift lever in 3


11 to 14 V
·

Ignition switch ON

·

Shift lever not in 3


Below 1 V
G40-11 (2) - C24-1 (E1) L - BR 2 shift position switch signal
·

Ignition switch ON

·

Shift lever in 2


11 to 14 V
·

Ignition switch ON

·

Shift lever not in 2


Below 1 V
G40-10 (L) - C24-1 (E1) G-R - BR L shift position switch signal
·

Ignition switch ON

·

Shift lever in L


11 to 14 V
·

Ignition switch ON

·

Shift lever not in L


Below 1 V
C24-18 (S1) - C24-1 (E1) GR - BR S1 solenoid signal 1st or 2nd gear 11 to 14 V
3rd or 4th gear Below 1 V
C24-17 (S2) - C24-1 (E1) W-L - BR S2 solenoid signal 2nd or 3rd gear 11 to 14 V
1st or 4th gear Below 1 V
C24-20 (SLT+) - C24-19 (SLT-) G-Y - L-B SLT solenoid signal Engine idling Pulse generation
C24-16 (SL) - C24-1 (E1) G - BR SL solenoid signal Vehicle speed 65 km/h (40 mph), lockup (ON to OFF) Pulse generation
(See waveform 1)
Vehicle driving under look-up condition 11 to 14 V
C24-24 (THOC) - C24-23 (E2) BR - B-Y ATF temperature sensor signal ATF temperature: 115°C (239°F) or higher Below 1.5 V
C24-30 (SP2+) - C24-29 (SP2-) R - G Speed sensor SP2 signal Vehicle speed 20 km/h (12 mph) Pulse generation
(See waveform 2)
C24-3 (NC0+) - C24-2 (NC0-) V - P Speed sensor NC0 signal Engine idling
(shift lever in P or N)
Pulse generation
(See waveform 3)
G40-15 (L4) - C24-1 (E1) G-W - BR L4 position signal
·

Ignition switch ON

·

Transfer in L4


Below 1 V
·

Ignition switch ON

·

Transfer not in L4


11 to 14 V
G41-25 (SPD1) - C24-1 (E1) V-R - BR Speed signal Vehicle speed 20 km/h (12 mph) Pulse generation
(See waveform 4)
G41-14 (STP) - C24-1 (E1) G-W - BR STP light switch signal Brake pedal is depressed 7.5 to 14 V
Brake pedal is released Below 1 V
C24-11 (STA) - C24-1 (E1) B-Y - BR Starter signal Cranking 6 V or more
G40-16 (TFN) - C24-1 (E1) W-G - BR N shift position switch signal
·

Ignition switch ON

·

Transfer shift lever on N


Below 1 V
·

Ignition switch ON

·

Transfer shift lever not on N


11 to 14 V
G41-6 (IG2) - C24-1 (E1) B-O - BR Ignition switch Ignition switch ON 11 to 14 V
G41-21 (CAN+) - C24-1 (E1) V - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 5)
G41-20 (CAN-) - C24-1 (E1) P - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 6)

a.
C170572
2.479,0.854 3.135,1.052 0.656,0.198 10 false 10 V/DIV. 2.625,1.625 3.042,1.823 0.417,0.198 10 false GND 1.344,2.594 2.375,2.781 1.031,0.188 10 false 100 msec./DIV.

Using an oscilloscope, check waveform 1.

Reference
Terminal No. (Symbol) Tool Setting Condition
C24-16 (SL) - C24-1 (E1) 10 V/DIV., 100 msec./DIV. Vehicle speed 65 km/h (40 mph), lockup (ON to OFF)


b.
C170571
2.482,0.857 3.138,1.058 0.656,0.201 10 2 V/DIV. 2.624,1.58 3.036,1.783 0.412,0.203 10 GND 1.342,2.599 2.392,2.787 1.05,0.188 10 20 msec./DIV.

Using an oscilloscope, check waveform 2.

Reference
Terminal No. (Symbol) Tool Setting Condition
C24-30 (SP2+) - C24-29 (SP2-) 2 V/DIV., 20 msec./DIV. Vehicle speed 20 km/h (12 mph)


c.
C170570
2.479,0.896 3.135,1.094 0.656,0.198 10 false 5 V/DIV. 2.625,1.625 3.042,1.823 0.417,0.198 10 false GND 1.344,2.594 2.302,2.781 0.958,0.188 10 false 0.5 msec./DIV.

Using an oscilloscope, check waveform 3.

Reference
Terminal No. (Symbol) Tool Setting Condition
C24-3 (NC0+) - C24-2 (NC0-) 5 V/DIV., 0.5 msec./DIV. Engine idling (shift lever in P or N)


d.
C170574
2.479,0.865 3.135,1.063 0.656,0.198 10 false 5 V/DIV. 2.625,1.833 3.042,2.031 0.417,0.198 10 false GND 1.344,2.594 2.302,2.781 0.958,0.188 10 false 20 msec./DIV.

Using an oscilloscope, check waveform 4.

Reference
Terminal No. (Symbol) Tool Setting Condition
G41-25 (SPD1) - C24-1 (E1) 5 V/DIV., 20 msec./DIV. Vehicle speed 20 km/h (12 mph)


e.
C175015
2.5,0.844 3.156,1.042 0.656,0.198 10 false 1 V/DIV. 2.646,2.083 3.063,2.281 0.417,0.198 10 false GND 1.344,2.677 2.302,2.865 0.958,0.188 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 5.

Reference
Terminal No. (Symbol) Tool Setting Condition
G41-21 (CAN+) - C24-1 (E1) 1 V/DIV., 10 μsec./DIV. Ignition switch ON


f.
C175016
2.5,0.833 3.156,1.031 0.656,0.198 10 false 1 V/DIV. 2.646,2.083 3.063,2.281 0.417,0.198 10 false GND 1.344,2.667 2.302,2.854 0.958,0.188 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 6.

Reference
Terminal No. (Symbol) Tool Setting Condition
G41-20 (CAN-) - C24-1 (E1) 1 V/DIV., 10 μsec./DIV. Ignition switch ON



CHECK ECM


C115871
1.348,0.046 1.706,0.26 0.357,0.214 1.401,0.081 1.776,0.292 0.375,0.211 10 C22 2.816,0.046 3.173,0.26 0.357,0.214 4.292,0.046 4.649,0.26 0.357,0.214 5.658,0.046 6.015,0.26 0.357,0.214 2.872,0.081 3.247,0.292 0.375,0.211 10 C23 4.34,0.081 4.715,0.292 0.375,0.211 10 G38 5.708,0.081 6.084,0.292 0.375,0.211 10 G39

HINT:

The standard voltage at each ECM terminal is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G39-1 (+B) - C23-7 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
G38-22 (CAN+) - C23-7 (E1) V - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
G38-21 (CAN-) - C23-7 (E1) P - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 2)

a.
C175015
2.5,0.844 3.156,1.042 0.656,0.198 10 false 1 V/DIV. 2.646,2.083 3.063,2.281 0.417,0.198 10 false GND 1.344,2.677 2.302,2.865 0.958,0.188 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 1.

Reference
Terminal No. (Symbol) Tool Setting Condition
G38-22 (CAN+) - C23-7 (E1) 1 V/DIV., 10 μsec./DIV. Ignition switch ON


b.
C175016
2.5,0.833 3.156,1.031 0.656,0.198 10 false 1 V/DIV. 2.646,2.083 3.063,2.281 0.417,0.198 10 false GND 1.344,2.667 2.302,2.854 0.958,0.188 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 2.

Reference
Terminal No. (Symbol) Tool Setting Condition
G38-21 (CAN-) - C23-7 (E1) 1 V/DIV., 10 μsec./DIV. Ignition switch ON