Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM C

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the TCM.

The gear shift point and lock-up timing are controlled by the TCM based on the signals from this vehicle speed sensor and the throttle position sensor signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0722 Output Speed Sensor Circuit No Signal

All conditions below are detected 500 times or more continuously (2-trip detection logic):

1.

No signal from speed sensor SP2 is input to TCM while 4 pulses of No. 1 vehicle speed sensor signal are sent

2.

Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.

3.

Park/neutral position switch is off

4.

Transfer position is not neutral



·

Open or short in speed sensor SP2 circuit

·

Speed sensor SP2

·

TCM

·

Automatic transmission (clutch, brake, gear, etc.)


Comes on DTC stored

Reference: Inspect using an oscilloscope.

Check the waveform of the TCM connector.

Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition
C24-30 (SP2+) - C24-29 (SP2-) 2 V/DIV., 20 msec./DIV. Vehicle speed 20 km/h (12 mph) Refer to illustration


C170571
2.458,0.885 3.115,1.083 0.656,0.198 10 false 2 V/DIV. 2.583,1.635 3,1.833 0.417,0.198 10 false GND 1.563,2.604 2.615,2.792 1.052,0.188 10 false 20 msec./DIV.

MONITOR DESCRIPTION

The output speed sensor SP2 monitors the output shaft speed. The TCM controls the gear shift point and lock-up timing based on the signals from the output speed sensor SP2 and throttle position sensor.

If the TCM detects no signal from the output speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C239151
5.635,1.115 6.115,1.323 0.479,0.208 10 false SP2+ 5.635,2.219 6.115,2.427 0.479,0.208 10 false SP2- 5.833,3.198 6.313,3.406 0.479,0.208 10 false TCM 5.833,3.01 6.167,3.219 0.333,0.208 10 false C24 0.563,2.531 1.938,2.729 1.375,0.198 10 false Speed Sensor SP2 0.563,2.344 0.865,2.542 0.302,0.198 10 false C13 5.354,2.354 5.583,2.563 0.229,0.208 10 false 29 5.354,1.219 5.583,1.427 0.229,0.208 10 false 30 1.281,1.292 1.417,1.5 0.135,0.208 10 false 1 1.292,2.073 1.438,2.281 0.146,0.208 10 false 2

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the tester, read the Data List.

Powertrain > ECT > Data List
Tester Display
SPD (SP2)
50003 64 161
Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph)
(output shaft speed is equal to vehicle speed)
-
HINT:
·

SPD (SP2) is always 0 while driving:

Open or short in the sensor or circuit.

·

The SPD (SP2) value displayed on the intelligent tester is much lower than the actual vehicle speed:

Sensor trouble, improper installation, or intermittent connection trouble in the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR SP2 INSTALLATION
a.
C211922
0.844,0.167 1.083,0.365 0.24,0.198 10 false *a 2.302,0.167 2.542,0.365 0.24,0.198 10 false *b
*a CORRECT
*b INCORRECT


Check the speed sensor SP2 installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



Result:
Proceed to
OK
NG



OK

2.INSPECT SPEED SENSOR SP2

NG

SECURELY INSTALL OR REPLACE SPEED SENSOR SP2

2.INSPECT SPEED SENSOR SP2
a.
C206284
1.302,1.708 1.604,1.135 true 2.146,1.719 1.854,1.146 true 0.083,0.094 0.323,0.292 0.24,0.198 10 false *a 1.198,1.75 1.646,1.948 0.448,0.198 10 false 2 2.156,1.75 2.604,1.948 0.448,0.198 10 false 1
*a Component without harness connected
(Speed Sensor SP2)


Disconnect the C13 speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - TCM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - TCM)
a.
C212047
0.792,0.24 1.208,0.49 0.417,0.25 0.667,2.156 0.458,2.813 true 0.729,2.156 1.313,2.833 true 0.073,0.094 0.271,0.26 0.198,0.167 10 false *a 0.854,0.281 1.156,0.438 0.302,0.156 10 false C24 0.177,2.875 0.885,3.104 0.708,0.229 10 false 30 (SP2+) 1.156,2.885 1.792,3.104 0.635,0.219 10 false 29 (SP2-)
*a Rear view of wire harness connector
(to TCM)


Disconnect the C24 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-30 (SP2+) - C24-29 (SP2-) 20°C (68°F) 560 to 680 Ω
C24-30 (SP2+) - Body ground Always 10 kΩ or higher
C24-29 (SP2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR