Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.10–2012.01
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM C

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0710  Transmission Fluid Temperature Sensor "A" Circuit  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the ATF temperature into a resistance value which is input into the TCM.

The Automatic Transmission Fluid (ATF) temperature sensor is on the transmission, just in front of the oil cooler inlet pipeline.

HINT:

The temperature of the ATF easily rises when towing, climbing hills, in traffic, etc.


Vehicle conditions when the sensor is normal and when the sensor is short-circuited are indicated in the table below.

ATF Temperature Sensor State Detection Condition Symptom Recovery Condition
Sensor is normal ATF temperature higher than 130°C (266°F) Shift point too low ATF temperature below 125°C (257°F)
When conditions (a) and (b) are satisfied:
(a) ATF temperature higher than 130°C (266°F)
(b) Engine coolant temperature higher than 98°C (208°F)
Lock-up in 4th or 3rd gear* ATF temperature below 110°C (230°F) and engine coolant temperature below 98°C (208°F)
Sensor is short-circuited Any conditions Shift point too low Symptoms still occur
Engine coolant temperature higher than 95°C (203°F) Lock-up in 4th or 3rd gear* Symptoms still occur

HINT:

*: When the ATF temperature is normal, transmission lock-up occurs in 4th gear with the shift lever in D and in 3rd gear with the shift lever in 3.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0710 Transmission Fluid Temperature Sensor "A" Circuit ATF temperature sensor resistance changes from (a) to (b) or from (b) to (a) in less than 0.5 sec., and P0712 and P0713 are not detected (1-trip detection logic):
(a) ATF temperature sensor resistance is less than 79 Ω
(b) ATF temperature sensor resistance is more than 156 kΩ
·

Open or short in ATF temperature sensor circuit

·

ATF temperature sensor

·

TCM


Comes on DTC stored
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
·

Short in ATF temperature sensor circuit

·

ATF temperature sensor

·

TCM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input When 15 minutes or more have elapsed after the engine is started, ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more (1-trip detection logic).
·

Open in ATF temperature sensor circuit

·

ATF temperature sensor

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature sensor is below 79 Ω or higher than 156 kΩ, the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C281620
0.521,2.615 2.167,2.865 1.646,0.25 10 false ATF Temperature Sensor 0.521,2.427 2.167,2.677 1.646,0.25 10 false C14 1.281,1.281 1.646,1.51 0.365,0.229 10 false 1 1.292,2.083 1.656,2.313 0.365,0.229 10 false 2 5.344,1.24 5.552,1.49 0.208,0.25 10 false 24 5.344,2.365 5.552,2.615 0.208,0.25 10 false 23 5.625,1.125 6.146,1.333 0.521,0.208 10 false THOC 5.635,2.229 6.156,2.438 0.521,0.208 10 false E2 5.844,3.042 6.365,3.25 0.521,0.208 10 false C24 5.844,3.219 6.198,3.438 0.354,0.219 10 false TCM

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the tester, read the Data List.

Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 3
50003 64 176
Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 3 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall test:

Approximately 80°C (176°F)

·

Equal to ambient temperature during engine is cold


If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited
HINT:

When DTC P0712 is output and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.

When DTC P0713 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the tester in order to check if a malfunction exists.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit



PROCEDURE

1.INSPECT ATF TEMPERATURE SENSOR
a.
C246821
2.219,1.708 1.917,1.125 true 1.25,1.698 1.552,1.115 true 0.094,0.052 0.333,0.25 0.24,0.198 10 false *a 2.219,1.75 2.667,1.948 0.448,0.198 10 false 1 1.146,1.729 1.594,1.927 0.448,0.198 10 false 2
*a Component without harness connected
(ATF Temperature Sensor)


Disconnect the C14 ATF temperature sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 79 Ω to 156 kΩ
1 - Body ground Always 10 kΩ or higher
2 - Body ground Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.


Standard Resistance:
ATF Temperature Specified Condition
20°C (68°F) 10.3 to 13.9 kΩ
120°C (248°F) 0.58 to 0.65 kΩ



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR - TCM)

NG

2.CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR - TCM)
a.
C212047
0.823,0.26 1.208,0.51 0.385,0.25 1.281,2.156 0.844,2.802 true 1.344,2.156 1.719,2.833 true 0.094,0.083 0.292,0.25 0.198,0.167 10 false *a 0.875,0.313 1.177,0.469 0.302,0.156 10 false C24 0.5,2.865 1.208,3.094 0.708,0.229 10 false 24 (THOC) 1.552,2.875 2.063,3.094 0.51,0.219 10 false 23 (E2)
*a Rear view of wire harness connector
(to TCM)


Disconnect the C24 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-24 (THOC) - C24-23 (E2) Always 79 Ω to 156 kΩ
C24-24 (THOC) - Body ground Always 10 kΩ or higher
C24-23 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR