Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.10–2012.10
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM C

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0818  Driveline Disconnect Switch Input Circuit  


DESCRIPTION

The TCM detects the signal from the transfer neutral position switch.

This DTC indicates that the transfer neutral position switch remains ON.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0818 Driveline Disconnect Switch Input Circuit Transfer neutral position switch remains ON while vehicle is running under following conditions for 30 sec. (2-trip detection logic):
·

Vehicle speed is 25 km/h (16 mph) or more

·

Transfer shift lever is on H


·

Short in transfer neutral position switch circuit

·

Transfer neutral position switch

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM detects whether or not the transfer shift lever is in neutral by monitoring the signal from the transfer neutral position switch.

If the transfer neutral position switch indicates that the transfer shift lever is in neutral under all of the following conditions, the TCM will conclude that there is a malfunction of the transfer neutral position switch.

·

The transfer shift lever is in the H position.

·

The vehicle is traveling at 25 km/h (16 mph) or more.

·

The transfer neutral position switch has been ON for more than 30 seconds.


Then the TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C154998
6.094,2.958 6.615,3.167 0.521,0.208 10 false TCM 5.896,1.302 6.417,1.51 0.521,0.208 10 false TFN 5.625,1.417 5.927,1.625 0.302,0.208 10 false 16 3.646,1.406 3.802,1.615 0.156,0.208 10 false 1 2.885,1.396 3.073,1.604 0.188,0.208 10 false 2 6.094,2.771 6.615,2.979 0.521,0.208 10 false G40 2.323,1.583 2.844,1.792 0.521,0.208 10 false C30 2.323,1.781 4.313,2.208 1.99,0.427 10 false No. 2 Transfer Indicator Switch (Transfer neutral position switch)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - BODY GROUND)
a.
C237850
0.344,1.042 0.781,1.302 0.438,0.26 0.083,0.063 0.344,0.281 0.26,0.219 10 false *a 0.406,1.083 0.75,1.25 0.344,0.167 10 false C30
*a Front view of wire harness connector
(to No. 2 Transfer Indicator Switch)


Disconnect the C30 No. 2 Transfer Indicator Switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Condition
C30-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT NO.2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO.2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)
a.
C237864
0.052,0.063 0.229,0.26 0.177,0.198 10 false *a 0.25,2.813 0.427,3.01 0.177,0.198 10 false *c 0.948,2.813 1.125,3.01 0.177,0.198 10 false *b
*a Component without harness connected
(No. 2 Transfer Indicator Switch)
*b Pushed
*c Not pushed


Remove the No. 2 transfer indicator switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
1 - 2 Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - TCM)

NG

REPLACE NO.2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - TCM)
a.

Disconnect the C30 No. 2 Transfer Indicator Switch connector.


b.

Disconnect the G40 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G40-16 (TFN) - C30-1 Always Below 1 Ω
G40-16 (TFN) or C30-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR