Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2012.10
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM D

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  MECHANICAL SYSTEM TESTS  


STALL SPEED TEST


HINT:

This test is for checking the overall performance of the engine and transmission.


CAUTION:
·

To ensure safety, perform this test in an open and level area that provides good traction.

·

The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.



NOTICE:

Do not perform the stall speed test for more than 5 seconds.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Data List.

Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 3
50003 64 176

e.

Run the vehicle until the transmission fluid temperature is between 50 and 80°C (122 and 176°F).


f.

Allow the engine to idle with the air conditioning off.


g.

Chock all 4 wheels.


h.

Set the parking brake and keep the brake pedal depressed firmly with your left foot.


i.

Move the shift lever to D.


j.

Depress the accelerator pedal as much as possible with your right foot.


k.

Read the engine speed (stall speed) and release the accelerator pedal immediately.

Standard value:

2500 +/-200 rpm


Evaluation
Test Result Possible Cause
Stall speed is less than standard value
·

Line pressure is low

·

Forward clutch slipping

·

No. 2 one-way clutch is not operating properly

·

O/D one-way clutch is not operating properly


Stall speed is more than standard value
·

Line pressure is low

·

Improper fluid level

·

O/D one-way clutch is not operating properly



NOTICE:

Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).




SHIFT TIME LAG TEST


HINT:

This test is to check the condition of the direct clutch, forward clutch, 1st brake and reverse brake.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Data List.

Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 3
50003 64 176

e.

Run the vehicle until the transmission fluid temperature is between 50 and 80°C (122 and 176°F).


f.

Allow the engine to idle with the air conditioning off.


g.

Set the parking brake and keep the brake pedal depressed firmly.


h.

Check the D position time lag.

i.

Move the shift lever to N and wait for 1 minute.


ii.

Move the shift lever to D and measure the time until the shock is felt.


iii.

Repeat the 2 procedures above 3 times, and then calculate the average time of the 3 tests.



i.

Check the R position time lag.

i.

Move the shift lever to N and wait for 1 minute.


ii.

Move the shift lever to R and measure the time until the shock is felt.


iii.

Repeat the 2 procedures above 3 times, and then calculate the average time of the 3 tests.

Standard value:

D position time lag is less than 1.2 seconds

R position time lag is less than 1.5 seconds


Evaluation
Test Result Possible Cause
D position time lag exceeds standard value
·

Line pressure is low

·

Forward clutch is worn

·

O/D one-way clutch is not operating properly


R position time lag exceeds standard value
·

Line pressure is low

·

Direct clutch is worn

·

1st and reverse brake is worn

·

O/D one-way clutch is not operating properly