Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.10–2012.04
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM C

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine rpm, required engine torques, warning indicators in the combination meter, DTCs and other data. The ECM sends signals to the TCM concerning engine rpm, opening angles of the throttle valve, temperature of the intake air and engine coolant, engine torques, and other data.

If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and set a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0100 Lost Communication with ECM / PCM "A" No communication from ECM for certain period of time (1-trip detection logic)
·

Open or short in TCM and ECM circuit

·

TCM

·

ECM


Comes on DTC stored

WIRING DIAGRAM

C239208
3.844,1 4.833,1.208 0.99,0.208 10 false from IGN Fuse 0.583,0.99 1.76,1.198 1.177,0.208 10 false from MAIN Relay 5.729,2.854 6.073,3.052 0.344,0.198 10 false E1 5.719,1 6.24,1.229 0.521,0.229 10 false IG2 5.344,1.01 5.74,1.188 0.396,0.177 10 false G41 5.354,2.875 5.719,3.063 0.365,0.188 10 false C24 5.354,2.354 5.677,2.542 0.323,0.188 10 false G41 5.354,1.833 5.802,2.021 0.448,0.188 10 false G41 5.427,0.844 5.604,1.031 0.177,0.188 10 false 6 5.417,2.708 5.573,2.896 0.156,0.188 10 false 1 5.396,2.177 5.625,2.365 0.229,0.188 10 false 20 5.406,1.656 5.813,1.844 0.406,0.188 10 false 21 5.708,1.823 6.323,2.052 0.615,0.229 10 false CAN+ 5.708,2.333 6.208,2.521 0.5,0.188 10 false CAN- 3.052,1.823 3.49,2.01 0.438,0.188 10 false CAN+ 2.313,1.01 2.646,1.188 0.333,0.177 10 false G39 2.385,0.833 2.583,1.01 0.198,0.177 10 false 1 3.521,1.833 3.813,2.01 0.292,0.177 10 false G38 3.573,1.646 3.771,1.823 0.198,0.177 10 false 22 3.531,2.354 3.854,2.531 0.323,0.177 10 false G38 3.583,2.177 3.781,2.354 0.198,0.177 10 false 21 2.313,2.875 2.583,3.052 0.271,0.177 10 false C23 2.406,2.698 2.552,2.875 0.146,0.177 10 false 7 2.667,0.99 3.104,1.177 0.438,0.188 10 false +B 2.667,2.854 3.104,3.042 0.438,0.188 10 false E1 3.073,2.333 3.51,2.521 0.438,0.188 10 false CAN- 6.01,3.344 6.49,3.542 0.479,0.198 10 false TCM 2.885,3.344 3.271,3.542 0.385,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


NOTICE:

If the ECM is replaced, the new ECM needs initialization.


PROCEDURE

1.CHECK ECM (+B VOLTAGE, E1 GROUND)
a.
C238415
1.198,0.75 1.635,1.01 0.438,0.26 2.427,0.75 2.865,1.01 0.438,0.26 0.938,2.344 1.167,1.51 true 2.979,2.344 2.823,1.51 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.271,0.802 1.583,0.979 0.313,0.177 10 false C23 2.5,0.802 2.813,0.979 0.313,0.177 10 false G39 0.729,2.396 1.146,2.594 0.417,0.198 10 false 7 (E1) 2.781,2.406 3.25,2.604 0.469,0.198 10 false 1 (+B)
*a Rear view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G39-1 (+B) - Body ground Ignition switch ON 11 to 14 V



b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Condition
C23-7 (E1) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK A
NG (ECD system w/ EGR cooler) B
NG (ECD system w/o EGR cooler) C




A

2.CHECK TCM (IG2 VOLTAGE, E1 GROUND)

B

C

2.CHECK TCM (IG2 VOLTAGE, E1 GROUND)
a.
C212050
2.219,0.698 2.656,0.958 0.438,0.26 0.802,0.698 1.24,0.958 0.438,0.26 2.188,1.531 2.375,2.5 true 1.313,1.521 1.104,2.49 true 2.188,2.563 2.698,2.771 0.51,0.208 10 false 6 (IG2) 0.906,2.521 1.385,2.729 0.479,0.208 10 false 1 (E1) 0.073,0.063 0.26,0.219 0.188,0.156 10 false *a 2.281,0.74 2.583,0.917 0.302,0.177 10 false G41 0.865,0.74 1.167,0.917 0.302,0.177 10 false C24
*a Rear view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G41-6 (IG2) - Body ground Ignition switch ON 11 to 14 V



b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the G38 ECM connector.


b.

Disconnect the G41 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-22 (CAN+) - G41-21 (CAN+) Always Below 1 Ω
G38-21 (CAN-) - G41-20 (CAN-) Always Below 1 Ω
G38-22 (CAN+) or G41-21 (CAN+) - Body ground Always 10 kΩ or higher
G38-21 (CAN-) or G41-20 (CAN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CONFIRM DTC
a.

Clear the DTC.

Powertrain > ECT > Clear DTCs
50002 64

b.

Replace the TCM.

HINT:

Replace the TCM with a TCM from a normally functioning vehicle of the same model.



c.

Start the engine.


d.

Read the DTCs.

Powertrain > ECT > Trouble Codes
50001 64
Result:
Result Proceed to
U0100 is output A
U0100 is not output B




A

B