Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM C

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2769  Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL)  P2770  Torque Converter Clutch Solenoid Circuit High (Shift Solenoid Valve SL)  


DESCRIPTION

The shift solenoid valve SL is turned on and off by signals from the TCM to control the hydraulic pressure acting on the lock-up relay valve, which then controls the operation of the lock-up clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2769 Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL) TCM detects short in shift solenoid valve SL circuit (once) when shift solenoid valve SL is operated (2 trip detection logic *1 , 1 trip detection logic *2)
·

Short in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

TCM


Comes on ( w/ OBD)-(w/o OBD) DTC stored
P2770 Torque Converter Clutch Solenoid Circuit High (Shift Solenoid Valve SL) TCM detects open in shift solenoid valve SL circuit (once) when shift solenoid valve SL is not operated (2 trip detection logic *1 , 1 trip detection logic *2)
·

Open in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

TCM


Comes on ( w/ OBD)-(w/o OBD) DTC stored

*1: w/ OBD

*2: w/o OBD

Fail-safe function:

If the TCM detects a malfunction, it turns the shift solenoid valve SL off.

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the TCM based on engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and shift position selection. The TCM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input rpm (NC0). The TCM calculates the actual transmission gear by comparing the input rpm (NC0) to the output rpm (SP2). When conditions are appropriate, the TCM requests "lock-up" by applying control voltage to the shift solenoid valve SL. When the shift solenoid valve SL is opened, the shift solenoid valve SL applies pressure to the lock-up relay valve and locks the torque converter clutch. If the TCM detects an open or short in the shift solenoid valve SL circuit, the TCM interprets this as a fault in the shift solenoid valve SL or its circuit. The TCM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C237838
2.479,0.906 2.896,1.115 0.417,0.208 10 false SL 5.729,0.979 5.99,1.188 0.26,0.208 10 false SL 1,1.688 2.51,1.896 1.51,0.208 10 false Shift Solenoid Valve SL 0.927,2.958 2.438,3.167 1.51,0.208 10 false Transmission Wire 0.927,2.771 1.271,2.958 0.344,0.188 10 false C12 5.958,3.271 6.49,3.479 0.531,0.208 10 false TCM 5.969,3.083 6.313,3.271 0.344,0.188 10 false C24 2.781,1.125 3.125,1.323 0.344,0.198 10 false 7 5.448,1.115 5.802,1.323 0.354,0.208 10 false 16

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.

Disconnect the C12 transmission wire connector.


b.
C214964
1.083,1.708 1.563,1.219 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.906,1.677 1.135,1.875 0.229,0.198 10 false SL
*a Component without harness connected
(Transmission Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL
2.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL - TCM)
a.
C212047
0.781,0.229 1.219,0.49 0.438,0.26 1.031,2.073 1.292,2.854 true 0.073,0.063 0.271,0.229 0.198,0.167 10 false *a 0.844,0.281 1.146,0.438 0.302,0.156 10 false C24 1.052,2.906 1.563,3.125 0.51,0.219 10 false 16 (SL)
*a Rear view of wire harness connector
(to TCM)


Disconnect the C24 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-16 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL
a.
C237973
0.115,0.094 0.365,0.313 0.25,0.219 10 false *a 3.063,0.469 3.302,0.688 0.24,0.219 10 false (+) 3.083,1.104 3.323,1.323 0.24,0.219 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL)


Remove shift solenoid valve SL.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SL connector terminal - Shift solenoid valve SL body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SL connector

·

Battery negative (-) → Shift solenoid valve SL body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG