The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) | One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic): ·
NSW input signal ·
R input signal ·
2 input signal ·
L input signal (B) All signals are OFF simultaneously for NSW, R, 2 and L positions (2-trip detection logic). (C) Any of the following signals is ON for 2.0 seconds or more with the shift lever in 3 (2-trip detection logic): ·
NSW input signal ·
R input signal ·
2 input signal ·
L input signal |
·
Open or short in park/neutral position switch circuit ·
Park/neutral position switch ·
Shift lock control ECU (Shift lock control unit assembly) ·
ECM |
Comes on | DTC stored |
This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (R, D, 3, 2 or L).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display |
|---|
| Neutral Position SW Signal |
| Shift SW Status (R Range) |
| Shift SW Status (2 Range) |
| Shift SW Status (L Range) |
| Shift SW Status (3 Range) |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Position SW Signal | PNP switch status | ON or OFF | ·
Shift lever in P or N: ON ·
Shift lever not in P or N: OFF |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP switch status | ON or OFF | ·
Shift lever in R: ON ·
Shift lever not in R: OFF |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (2 Range) | PNP switch status | ON or OFF | ·
Shift lever in 2: ON ·
Shift lever not in 2: OFF |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (L Range) | PNP switch status | ON or OFF | ·
Shift lever in L: ON ·
Shift lever not in L: OFF |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (3 Range) | PNP switch status | ON or OFF | ·
Shift lever in 3: ON ·
Shift lever not in 3: OFF |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch) |
Disconnect the C26 park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C26-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| C26-2 (RB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch) |
Disconnect the C26 park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C26-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| C26-4 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Park/Neutral Position Switch) |
Disconnect the C26 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 5 (L) | Shift lever in P | Below 1 Ω |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| 4 (B) - 5 (L) | Shift lever in N | Below 1 Ω |
| 2 (RB) - 7 (DL) | Shift lever in D or 3 | Below 1 Ω |
| 2 (RB) - 3 (2L) | Shift lever in 2 | Below 1 Ω |
| 2 (RB) - 8 (LL) | Shift lever in L | Below 1 Ω |
| 4 (B) - 5 (L) | Shift lever not in P | 10 kΩ or higher |
| 2 (RB) - 1 (RL) | Shift lever not in R | 10 kΩ or higher |
| 4 (B) - 5 (L) | Shift lever not in N | 10 kΩ or higher |
| 2 (RB) - 7 (DL) | Shift lever not in D or 3 | 10 kΩ or higher |
| 2 (RB) - 3 (2L) | Shift lever not in 2 | 10 kΩ or higher |
| 2 (RB) - 8 (LL) | Shift lever not in L | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>A343E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
| *a | Component without harness connected
(Shift Lock Control ECU) |
Disconnect the G37 shift lock control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (AT3) - 9 (NSSD) | Shift lever in 3 | Below 1 Ω |
| 3 (AT3) - 9 (NSSD) | Shift lever in D | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Disconnect the G37 shift lock control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 9 (NSSD) - Body ground | ·
Ignition switch ON ·
Shift lever in D or 3 |
11 to 14 V |
| 9 (NSSD) - Body ground | ·
Ignition switch ON ·
Shift lever not in D or 3 |
Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C97-17 (R) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever in R |
11 to 14 V* |
| G146-23 (3) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever in 3 |
11 to 14 V |
| C97-15 (2) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever in 2 |
11 to 14 V |
| C97-25 (L) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever in L |
11 to 14 V |
| C97-17 (R) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever not in R |
Below 1 V |
| G146-23 (3) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever not in 3 |
Below 1 V |
| C97-15 (2) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever not in 2 |
Below 1 V |
| C97-25 (L) - C98-5 (E1) | ·
Ignition switch ON ·
Shift lever not in L |
Below 1 V |
*: The voltage will drop slightly due to the illumination of the back-up light.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C26 park/neutral position switch connector.
Disconnect the G146 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C26-4 (B) - G146-24 (NSW) | Always | Below 1 Ω |
| C26-4 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG