The ATF (Automatic Transmission Fluid) temperature sensor converts the ATF temperature into a resistance value which is input into the ECM.
The Automatic Transmission Fluid (ATF) temperature sensor is on the transmission, just in front of the oil cooler inlet pipeline.
The temperature of the ATF easily rises when towing, climbing hills, in traffic, etc.
Vehicle conditions when the sensor is normal and when the sensor is short-circuited are indicated in the table below.
| ATF Temperature Sensor State | Detection Condition | Symptom | Recovery Condition |
|---|---|---|---|
| Sensor is normal | ATF temperature higher than 130°C (266°F) | Shift point too low | ATF temperature below 125°C (257°F) |
| When conditions (a) and (b) are satisfied:
(a) ATF temperature higher than 130°C (266°F) (b) Engine coolant temperature higher than 98°C (208°F) |
Lock-up in 4th or 3rd gear* | ATF temperature below 110°C (230°F) and engine coolant temperature below 98°C (208°F) | |
| Sensor is short-circuited | Any conditions | Shift point too low | Symptoms still occur |
| Engine coolant temperature higher than 95°C (203°F) | Lock-up in 4th or 3rd gear* | Symptoms still occur |
*: When the ATF temperature is normal, transmission lock-up occurs in 4th gear with the shift lever in D and in 3rd gear with the shift lever in 3.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low Input | ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic). | ·
Short in ATF temperature sensor circuit ·
ATF temperature sensor ·
ECM |
Comes on | DTC stored |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High Input | When 15 minutes or more have elapsed after the engine is started, ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more (1-trip detection logic). | ·
Open in ATF temperature sensor circuit ·
ATF temperature sensor ·
ECM |
Comes on | DTC stored |
The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature sensor is below 79 Ω or higher than 156 kΩ, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM will illuminate the MIL and store the DTC.
DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display |
|---|
| A/T Oil Temperature 3 |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Temperature 3 | ATF temperature sensor value | Min.: -40°C (-40°F)
Max.: 215°C (419°F) |
·
After stall test: Approximately 80°C (176°F) ·
Equal to ambient temperature when engine cold |
If the value is -40°C (-40°F) or 215°C (419°F), the ATF temperature sensor circuit is open or shorted. |
When DTC P0712 is output and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.
When DTC P0713 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.
Check the temperature displayed on the tester in order to check if a malfunction exists.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 150°C (302°F) or higher | Short circuit |
| *a | Component without harness connected
(ATF Temperature Sensor) |
Disconnect the C93 ATF temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 79 Ω to 156 kΩ |
| 1 - Body ground | Always | 10 kΩ or higher |
| 2 - Body ground | Always | 10 kΩ or higher |
If the resistance is out of the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
| ATF Temperature | Specified Condition |
|---|---|
| 20°C (68°F) | 10.3 to 13.9 kΩ |
| 120°C (248°F) | 0.58 to 0.65 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to ECM) |
Disconnect the C95 and C96 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C95-2 (THOC) - C96-16 (E2) | Always | 79 Ω to 156 kΩ |
| C95-2 (THOC) - Body ground | Always | 10 kΩ or higher |
| C96-16 (E2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG