This sensor detects the rotation speed of the turbine which indicates the input speed of the transmission. By comparing the input turbine speed signal NC0 with the output speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, and as a result, the gears shift smoothly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0717 | Turbine Speed Sensor Circuit No Signal | All conditions are met for 5 seconds or more (2-trip detection logic):
(a) Transmission input shaft speed is 300 rpm or less. (b) Transmission output shaft speed is 500 rpm or more. (c) Park/neutral position switch R input signal is off. |
·
Open or short in speed sensor NC0 circuit ·
Speed sensor NC0 ·
ECM ·
Automatic transmission (clutch, brake, gear, etc.) |
Comes on | DTC stored |
Reference: Inspect using an oscilloscope.
Check the waveform of the ECM connector.
| Terminal No. (Symbol) | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| C76-34 (NC0+) - C76-26 (NC0-) | 5 V/DIV., 0.5 msec./DIV. | Engine idling (shift lever in P or N) | Refer to illustration |
This DTC indicates that a pulse is not output from the speed sensor NC0 (turbine (input) speed sensor) or is output only a little. The NC0 terminal of the ECM detects the pulse signal from the speed sensor NC0 (input turbine speed). The ECM outputs a gear shift signal by comparing the input speed sensor NC0 signal with the output speed sensor SP2 signal.
If the input shaft speed is less than 300 rpm*1 although the output shaft speed is 500 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: A pulse is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (30 mph) or more.
DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display |
|---|
| SPD (NC0) |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SPD (NC0) | Input shaft speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Lock-up ON (after warming up engine): Input turbine speed (NC0) equal to engine speed ·
Lock-up OFF (idling with shift lever in N): Input turbine speed (NC0) nearly equal to engine speed |
Data is displayed in increments of 50 rpm. |
SPD (NC0) is always 0 while driving:
Open or short in the sensor or circuit.
SPD (NC0) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:
Sensor trouble, improper installation, or intermittent connection trouble in the circuit.
| *a | CORRECT |
| *b | INCORRECT |
Check the speed sensor NC0 installation.
The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the speed sensor connector.
| *a | Component without harness connected
(Speed Sensor NC0) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 560 to 680 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C76-34 (NC0+) - C76-26 (NC0-) | 20°C (68°F) | 560 to 680 Ω |
| C76-34 (NC0+) - Body ground | Always | 10 kΩ or higher |
| C76-26 (NC0-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG