Home › Drivetrain › A343F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1840EF _52 Drivetrain _009611 A343F AUTOMATIC TRANSMISSION / TRANSAXLE _0052478 AUTOMATIC TRANSMISSION SYSTEM C

A343F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

C237837
5.719,2.188 5.833,2.531 5.833,2.531 5.906,2.531 true 4.885,1.938 4.667,1.302 4.667,1.302 4.604,1.302 true 5.104,2.115 4.969,2.531 4.969,2.531 4.896,2.531 true 5.969,2.448 6.854,2.667 0.885,0.219 10 Solenoid Coil 0.26,0.448 1.51,0.667 1.25,0.219 10 Hydraulic Pressure 4.458,2.448 4.99,2.667 0.531,0.219 10 Sleeve 3.833,1.208 4.677,1.427 0.844,0.219 10 Spool Valve 2.75,2.979 3.313,3.198 0.563,0.219 10 Current

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current of shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) Open or short is detected in the shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C214969
1.76,2.854 3.094,3.052 1.333,0.198 10 Transmission Wire 1.76,2.688 2.156,2.885 0.396,0.198 10 C92 5.635,1.25 6.135,1.448 0.5,0.198 10 SLT+ 5.344,1.333 5.583,1.531 0.24,0.198 10 23 5.813,2.906 6.313,3.104 0.5,0.198 10 C96 5.813,3.083 6.313,3.281 0.5,0.198 10 ECM 3.469,1.125 3.969,1.323 0.5,0.198 10 SLT+ 3.938,1.354 4.177,1.552 0.24,0.198 10 2 1.49,1.729 3.219,1.927 1.729,0.198 10 Shift Solenoid Valve SLT 5.635,2.219 6.135,2.417 0.5,0.198 10 SLT- 5.344,2.323 5.583,2.521 0.24,0.198 10 24 3.479,2.052 3.979,2.25 0.5,0.198 10 SLT- 3.938,2.323 4.177,2.521 0.24,0.198 10 6 1.281,2.125 1.677,2.323 0.396,0.198 10 1 1.292,1.344 1.688,1.542 0.396,0.198 10 2

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C214964
1.833,0.948 2.479,0.531 true 2.417,1.698 1.875,1.229 true 0.083,0.042 0.396,0.24 0.313,0.198 10 false *a 2.49,1.635 2.885,1.833 0.396,0.198 10 false SLT- 2.542,0.438 2.948,0.635 0.406,0.198 10 false SLT+
*a Component without harness connected
(Transmission Wire)


Disconnect the C92 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SLT+) - 6 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
2 (SLT+) - Body ground Always 10 kΩ or higher
6 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C214336
1.781,0.292 2.219,0.552 0.438,0.26 1.438,2.667 1.854,2.094 true 2.323,2.667 1.896,2.094 true 0.052,0 0.323,0.198 0.271,0.198 10 false *a 1.021,2.698 1.688,2.896 0.667,0.198 10 false 24 (SLT-) 2.063,2.698 2.75,2.896 0.688,0.198 10 false 23 (SLT+) 1.875,0.333 2.25,0.563 0.375,0.229 10 false C96
*a Rear view of wire harness connector
(to ECM)


Disconnect the C96 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C96-23 (SLT+) - C96-24 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C96-23 (SLT+) - Body ground Always 10 kΩ or higher
C96-24 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928
1.75,0.969 2.198,0.385 true 1.479,0.958 1.021,0.375 true 1.76,2.948 2.208,2.354 true 1.479,2.948 1.021,2.354 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.24,0.25 2.406,0.448 0.167,0.198 10 false 1 0.917,0.24 1.083,0.438 0.167,0.198 10 false 2 2.25,2.198 2.417,2.396 0.167,0.198 10 false 1 0.917,2.229 1.083,2.427 0.167,0.198 10 false 2 1.927,3.969 2.125,4.167 0.198,0.198 10 false (-) 1.115,3.969 1.333,4.167 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLT)


Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG