Home › Drivetrain › A343F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.10–2012.10
RM1840EF _52 Drivetrain _009611 A343F AUTOMATIC TRANSMISSION / TRANSAXLE _0052478 AUTOMATIC TRANSMISSION SYSTEM U

A343F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the tester, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

Shift lever in P or N: ON

·

Shift lever not in P or N: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


Stop Light Switch Stop light switch status ON or OFF
·

Brake pedal depressed: ON

·

Brake pedal released: OFF


-
SPD (NC0) Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up ON (after warming up engine): Input turbine speed (NC0) equal to engine speed

·

Lock-up OFF (idling with shift lever in N): Input turbine speed (NC0) nearly equal to engine speed


Data is displayed in increments of 50 rpm.
SPD (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) -
Shift SW Status (R Range) PNP switch status ON or OFF
·

Shift lever in R: ON

·

Shift lever not in R: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


Shift SW Status (2 Range) PNP switch status ON or OFF
·

Shift lever in 2: ON

·

Shift lever not in 2: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


Shift SW Status (L Range) PNP switch status ON or OFF
·

Shift lever in L: ON

·

Shift lever not in L: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


Shift SW Status (3 Range) PNP switch status ON or OFF
·

Shift lever in 3: ON

·

Shift lever not in 3: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


A/T Oil Temperature 3 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall test: Approximately 80°C (176°F)

·

Equal to ambient temperature when engine cold


If the value is -40°C (-40°F) or 215°C (419°F), the ATF temperature sensor circuit is open or shorted.
Lock Up Lock-up ON or OFF
·

Lock-up operating: ON

·

Lock-up not operating: OFF


-
Shift Status ECM gear shift command 1st, 2nd, 3rd or 4th
·

Shift lever in D: 1st, 2nd, 3rd or 4th

·

Shift lever in 3: 1st, 2nd or 3rd

·

Shift lever in 2: 1st or 2nd

·

Shift lever in L: 1st


-
SLT Solenoid Status Shift solenoid SLT status ON or OFF
·

Accelerator pedal depressed: OFF

·

Accelerator pedal released: ON


-
SL Solenoid Status Shift solenoid SL status ON or OFF
·

Shift solenoid SL operating: ON

·

Shift solenoid SL not operating: OFF


-
HINT:

*: Refer to DTC P0705 (See page Drivetrain>A343F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>P0705).




PERFORM ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Solenoid (SLT) Operate the shift solenoid valve SLT and raise line pressure ON or OFF
HINT:
·

OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off)

·

ON: No action (normal operation)



[Vehicle Condition]
·

Vehicle stopped

·

Engine idling


Activate the Solenoid (S1) Operate the shift solenoid valve S1 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (S2) Operate the shift solenoid valve S2 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Lock Up Control shift solenoid valve SL to set automatic transmission to lock-up ON or OFF Possible to check shift solenoid valve SL operation.
[Vehicle Condition]
·

Throttle valve opening angle: Less than 35%

·

Vehicle speed: 60 km/h (36 mph) or more


Activate the Solenoid (SL) Operate the shift solenoid valve SL ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less
HINT:

"Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>A343F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>HYDRAULIC TEST) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.