Home › Drivetrain › A343F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.10–2012.10
RM1840EF _52 Drivetrain _009611 A343F AUTOMATIC TRANSMISSION / TRANSAXLE _0052478 AUTOMATIC TRANSMISSION SYSTEM C

A343F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the No. 1 transfer indicator switch (L4 position switch).

This DTC indicates that the transfer L4 position switch remains on.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance

Transfer L4 position switch remains on while vehicle is being driven under following conditions for 1.8 seconds or more (1-trip detection logic):

1.

Output shaft speed is 3000 rpm or less

2.

Transfer shift lever is in H



·

Short in transfer L4 position switch circuit

·

Transfer L4 position switch

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the transfer L4 position switch to determine when the transfer-case L4 gear is engaged. If the L4 position switch indicates that the transfer-case L4 gears are engaged under all of the following conditions, the ECM will conclude that there is a malfunction of the transfer L4 position switch:

·

Transfer-case shift lever is in H.

·

Transfer-case output shaft speed is between 750 and 3000 rpm.

·

The specified time period has elapsed.


Then the ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C154998
6.094,2.938 6.615,3.146 0.521,0.208 10 ECM 5.938,1.323 6.458,1.531 0.521,0.208 10 L4 5.635,1.396 5.938,1.604 0.302,0.208 10 14 3.646,1.406 3.802,1.615 0.156,0.208 10 1 2.865,1.406 3.052,1.615 0.188,0.208 10 2 6.094,2.76 6.615,2.969 0.521,0.208 10 G145 2.323,1.583 2.844,1.792 0.521,0.208 10 C29 2.323,1.781 4.229,2.198 1.906,0.417 10 No. 1 Transfer Indicator Switch (L4 Position Switch)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - BODY GROUND)
a.
C237849
0.083,0.015 0.359,0.223 0.276,0.208 10 *a 0.326,0.935 0.764,1.199 0.439,0.263 0.385,0.975 0.669,1.172 0.283,0.197 10 C29
*a Front view of wire harness connector
(to No. 1 Transfer Indicator Switch)


Disconnect the C29 No. 1 transfer indicator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT NO.1 TRANSFER INDICATOR SWITCH (L4 POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO.1 TRANSFER INDICATOR SWITCH (L4 POSITION SWITCH)
a.
C237865
0.052,0 0.229,0.198 0.177,0.198 10 *a 0.229,2.865 0.406,3.063 0.177,0.198 10 *c 0.969,2.885 1.146,3.083 0.177,0.198 10 *b
*a Component without harness connected
(No. 1 Transfer Indicator Switch)
*b Pushed
*c Not pushed


Remove the No. 1 transfer indicator switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
1 - 2 Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - ECM)

NG

REPLACE NO.1 TRANSFER INDICATOR SWITCH (L4 POSITION SWITCH)

3.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - ECM)
a.

Disconnect the C29 No. 1 transfer indicator switch connector.


b.

Disconnect the G145 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-1 - G145-14 (L4) Always Below 1 Ω
C29-1 or G145-14 (L4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR