Home › Drivetrain › A343F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM1840EF _52 Drivetrain _009611 A343F AUTOMATIC TRANSMISSION / TRANSAXLE _0052489 AUTOMATIC TRANSMISSION UNIT G

A343F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  INSPECTION  


PROCEDURE

Hide 1.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.

Remove the magnets and use them to collect steel particles.


b.

Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

·

Steel (magnetic): bearing, gear and clutch plate wear.

·

Brass (non-magnetic): bush wear.



Hide 2.INSPECT OVERDRIVE 1-WAY CLUTCH

AT08138
1.5,0.729 1.552,0.677 false
V100135

Lock
V100136

Free


a.

Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.


Hide 3.INSPECT OVERDRIVE DIRECT CLUTCH DISC

C212466

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes.



Hide 4.INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

C212467

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

15.8 mm (0.622 in.)


If the length is not as specified, replace the overdrive clutch return spring sub-assembly.


Hide 5.INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

AT08150

a.

Check that the check ball is free by shaking the piston.


b.

Check that the valve does not have leaks by applying low-pressure compressed air.

If the result is not as specified, replace the overdrive direct clutch piston sub-assembly.


Hide 6.INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

C213737

a.

Using a dial indicator, measure the inside diameter of the clutch drum bushes.

Standard inside diameter:

27.037 to 27.063 mm (1.0645 to 1.0654 in.)


If the inside diameter is not as specified, replace the overdrive direct clutch drum sub-assembly.


Hide 7.INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY

AT08143

a.

Using a dial indicator, measure the inside diameter of the planetary gear bush.

Standard inside diameter:

11.200 to 11.221 mm (0.4409 to 0.4417 in.)


If the inside diameter is not as specified, replace the overdrive planetary gear assembly.


b.
AT04450

Using a feeler gauge, measure the planetary pinion gear thrust clearance.

Standard clearance:

0.20 to 0.60 mm (0.00788 to 0.0236 in.)


If the clearance is not as specified, replace the overdrive planetary gear assembly.


Hide 8.INSPECT OVERDRIVE BRAKE DISC

C212469

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes.



Hide 9.INSPECT PISTON OPERATION OF OVERDRIVE BRAKE

AT08451

a.

Place the overdrive support assembly onto the direct clutch assembly.


b.
AT08149

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.


Hide 10.INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

C212468

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.03 mm (0.671 in.)


If the length is not as specified, replace the overdrive brake return spring sub-assembly.


Hide 11.INSPECT DIRECT CLUTCH DISC

C212470

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes.



Hide 12.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C212471

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.32 mm (0.839 in.)


If the length is not as specified, replace the direct clutch return spring sub-assembly.


Hide 13.INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY

D001424

a.

Check that the check ball is free by shaking the piston.


b.

Check that the valve does not have leaks by applying low-pressure compressed air.


Hide 14.INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY

D001352

a.

Using a dial indicator, measure the inside diameter of the clutch drum bush.

Standard inside diameter:

53.915 to 53.94 mm (2.1227 to 2.1236 in.)


If the inside diameter is not as specified, replace the direct clutch drum sub-assembly.


Hide 15.INSPECT FORWARD CLUTCH DISC

C212473

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes.



Hide 16.INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY

D001424

a.

Check that the check ball is free by shaking the piston.


b.

Check that the valve does not have leaks by applying low-pressure compressed air.


Hide 17.INSPECT INPUT SHAFT SUB-ASSEMBLY

AT08171

a.

Using a dial indicator, measure the inside diameter of the input shaft bush.

Standard inside diameter:

24.000 to 24.026 mm (0.9449 to 0.9459 in.)


If the inside diameter is not as specified, replace the input shaft sub-assembly.


Hide 18.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C212474

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

19.47 mm (0.767 in.)


If the length is not as specified, replace the forward clutch return spring sub-assembly.


Hide 19.INSPECT SECOND COAST BRAKE PISTON ROD

AT07705

a.

Check the piston rod length.

HINT:

There are 2 different standard lengths for the piston rod.


Piston Rod Length:
Groove Mark Length
Without 78.3 to 78.5 mm (3.083 to 3.090 in.)
With 79.8 to 80.0 mm (3.142 to 3.149 in.)


If the length is not as specified, replace the rod with a new one even if the brake band works normally.


Hide 20.INSPECT SECOND COAST BRAKE BAND ASSEMBLY

D025701
1.26,1.177 0.844,0.542 0.844,0.542 0.75,0.542 true 0.573,0.448 0.875,0.698 0.302,0.25 10 false *1
*1 Printed Number


NOTICE:
·

If the lining of the brake band is peeled off or discolored, or if any part of the printed numbers is damaged, replace the brake band.

·

When installing a new band, soak it in ATF for at least 15 minutes before installation.



Hide 21.INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY

AT08187

a.

Using a dial indicator, measure the inside diameter of the planetary ring gear bush.

Standard inside diameter:

24.000 to 24.026 mm (0.9449 to 0.9459 in.)


If the inside diameter is not as specified, replace the front planetary ring gear sub-assembly.


Hide 22.INSPECT FRONT PLANETARY GEAR ASSEMBLY

D029743

a.

Using a feeler gauge, measure the pinion gear thrust clearance.

Standard clearance:

0.20 to 0.60 mm (0.00788 to 0.0236 in.)


If the clearance is not as specified, replace the front planetary gear assembly.


Hide 23.INSPECT NO. 1 1-WAY CLUTCH ASSEMBLY

AT08440
1.958,0.271 1.979,0.271 false
V100135

Lock
V100136

Free


a.

Hold the planetary sun gear and turn the 1-way clutch assembly. Check that the 1-way clutch hub can be turned clockwise freely and locks when turned counterclockwise.


Hide 24.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

AT08337

a.

Using a dial indicator, measure the inside diameter of the planetary sun gear bushes.

Standard inside diameter:

27.000 to 27.026 mm (1.0630 to 1.0640 in.)


If the inside diameter is not as specified, replace the planetary sun gear sub-assembly.


Hide 25.INSPECT SECOND BRAKE PISTON

AT08439

a.

Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.


Hide 26.INSPECT SECOND BRAKE DISC

C212478

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes.



Hide 27.INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C212479

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

16.05 mm (0.632 in.)


If the length is not as specified, replace the second brake piston return spring sub-assembly.


Hide 28.INSPECT FIRST AND REVERSE BRAKE DISC

C212463

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes.



Hide 29.INSPECT NO. 2 1-WAY CLUTCH

AT08200
2.073,0.542 2.115,0.479 false
V100135

Lock
V100136

Free


a.

Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.


Hide 30.INSPECT REAR PLANETARY GEAR ASSEMBLY

AT04459

a.

Using a feeler gauge, measure the thrust clearance.

Standard clearance:

0.20 to 0.60 mm (0.00788 to 0.0236 in.)


If the clearance is not as specified, replace the rear planetary gear assembly.


Hide 31.INSPECT FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C212464

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

12.902 mm (0.508 in.)


If the length is not as specified, replace the first and reverse brake return spring sub-assembly.


Hide 32.INSPECT TRANSMISSION CASE BUSH

AT08224

a.

Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.

Standard inside diameter:

38.113 to 38.138 mm (1.50051 to 1.50149 in.)


If the inside diameter is not as specified, replace the automatic transmission case sub-assembly.


Hide 33.INSPECT PISTON OPERATION OF FIRST AND REVERSE BRAKE

AT05258

a.

Make sure the first and reverse brake pistons move smoothly when compressed air is applied into the transmission case.


Hide 34.INSPECT PISTON OPERATION OF SECOND COAST BRAKE

AT05216
2.885,1.073 3.094,1.729 3.094,1.729 3.198,1.729 true 2.823,1.073 2.604,1.729 2.604,1.729 2.51,1.729 true 3.229,1.625 3.427,1.802 0.198,0.177 10 false *2 2.323,1.625 2.583,1.813 0.26,0.188 10 false *1
*1 Mark
*2 Piston Rod


a.

Place a mark on the second coast brake piston rod.


b.
AT05217
1.625,1.167 0.75,1.781 true 0.417,1.729 0.813,1.927 0.396,0.198 10 false SST

Using SST, measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

SST
09240-00020  

Standard piston stroke:

1.5 to 3.0 mm (0.0591 to 0.118 in.)


If the stroke is not as specified, replace the brake band with a new one.


Hide 35.INSPECT OUTPUT SHAFT END PLAY

C241556

a.

Using a dial indicator, measure the end play of the output shaft while moving it by hand.

Standard end play:

0.30 to 1.04 mm (0.0119 to 0.0409 in.)


If the end play is not as specified, check for improper installation.


b.

Check that the output shaft rotates smoothly.