The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the TCM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock-up timing are controlled by the TCM based on the signals from this vehicle speed sensor and the throttle position sensor signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0722 | Output Speed Sensor Circuit No Signal | All conditions are met 500 times or more continuously (2-trip detection logic):
(a) No signal from speed sensor SP2 is input to the TCM while 4 pulses of the No. 1 vehicle speed sensor signal are sent. (b) Vehicle speed is 9 km/h (6 mph) or more for at least 5 sec. (c) Park/neutral position switch is OFF. (c) Park/neutral position switch is OFF. (d) Transfer is not in neutral. |
·
Open or short in speed sensor SP2 circuit ·
Speed sensor SP2 ·
TCM ·
Automatic transmission (clutch, brake, gear, etc.) |
Comes on | DTC stored |
Reference: Inspect using an oscilloscope.
Check the waveform of the TCM connector.
| Terminal No. (Symbol) | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| C24-30 (SP2+) - C24-29 (SP2-) | 2 V/DIV., 20 msec./DIV. | Vehicle speed 20 km/h (12 mph) | Refer to illustration |
The output speed sensor SP2 monitors the output shaft speed. The TCM controls the gear shift point and lock-up timing based on the signals from the output speed sensor SP2 and throttle position sensor.
If the TCM detects no signal from the output shaft speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The TCM will illuminate the MIL and store a DTC.
DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| SPD (SP2) |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SPD (SP2) | Output shaft speed | Min.: 0 km/h (mph)
Max.: 255 km/h (158 mph) |
Vehicle stopped: 0 km/h (0 mph)
(output shaft speed equal to vehicle speed) |
- |
SPD (SP2) is always 0 while driving:
Open or short in the sensor or circuit.
The SPD (SP2) value displayed on the GTS is much lower than the actual vehicle speed:
Sensor trouble, improper installation, or intermittent connection trouble in the circuit.
| *a | CORRECT |
| *b | INCORRECT |
Check the speed sensor SP2 installation.
The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Speed Sensor SP2) |
Disconnect the speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 560 to 680 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to TCM) |
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-30 (SP2+) - C24-29 (SP2-) | 20°C (68°F) | 560 to 680 Ω |
| C24-30 (SP2+) - Body ground | Always | 10 kΩ or higher |
| C24-29 (SP2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG