Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) › from 2012.04
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052493 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High Stop light switch remains on even when the vehicle is driven in a stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) pattern 5 times (2-trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during stop and go driving, the TCM interprets this as a fault in the stop light switch. Then the MIL illuminates and the TCM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) 5 times for 2 driving cycles in order for the DTC to be stored.

WIRING DIAGRAM

C146704
5.688,3.031 6.198,3.24 0.51,0.208 10 false TCM 5.677,2.875 6.188,3.083 0.51,0.208 10 false G41 5.5,1.385 6.01,1.594 0.51,0.208 10 false STP 3.844,1.75 4.302,1.958 0.458,0.208 10 false A24 3.823,1.927 4.99,2.135 1.167,0.208 10 false Stop Light Switch 3.01,1.542 3.521,1.75 0.51,0.208 10 false STOP 2.073,1.552 2.583,1.76 0.51,0.208 10 false ALT 5.24,1.479 5.438,1.688 0.198,0.208 10 false 14 4.719,1.479 4.875,1.688 0.156,0.208 10 false 1 3.948,1.49 4.104,1.698 0.156,0.208 10 false 2 1.635,2.417 2.156,2.625 0.521,0.208 10 false Battery

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display
Stop Light Switch
50003 64 204
Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-


PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C228781
0.74,3.01 0.635,2.438 0.635,2.438 0.469,2.438 false 1.531,1.323 1.031,1.615 true 1.896,1.323 2.427,1.615 true 1.844,1.125 2.417,0.719 true 1.573,1.125 1.031,0.708 true 0.896,0.615 1.021,0.813 0.125,0.198 10 false 2 2.469,0.604 2.604,0.802 0.135,0.198 10 false 1 0.917,1.542 1.042,1.74 0.125,0.198 10 false 4 2.479,1.531 2.625,1.729 0.146,0.198 10 false 3 0.302,3.771 0.49,3.969 0.188,0.198 10 false *b 1.031,3.771 1.219,3.969 0.188,0.198 10 false *c 0.281,2.344 0.469,2.542 0.188,0.198 10 false *1 0.063,0 0.375,0.198 0.313,0.198 10 false *a
*1 Pin
*a Component without harness connected
(Stop Light Switch )
*b Not pushed
*c Pushed


Remove the stop light switch.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin pushed
(pedal released)
10 kΩ or higher
3 - 4 Pin not pushed
(pedal depressed)
10 kΩ or higher
1 - 2 Pin not pushed
(pedal depressed)
Below 1 Ω
3 - 4 Pin pushed
(pedal released)
Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TCM - BATTERY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (TCM - BATTERY)
a.
C212049
2.208,0.375 2.615,0.635 0.406,0.26 1.927,2.583 2.333,2.073 true 1.573,2.604 2.802,2.802 1.229,0.198 10 false 14 (STP) 2.271,0.417 2.948,0.615 0.677,0.198 10 false G41 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G41-14 (STP) - Body ground Brake pedal depressed 11 to 14 V
G41-14 (STP) - Body ground Brake pedal released Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR