Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) › from 2012.04
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052493 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the TCM. If an open or short circuit occurs in one of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)>FAIL-SAFE CHART).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) The TCM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears (1-trip detection logic).
Output signal duty ratio equals 100%.
HINT:

SL2 output signal duty is less than 100% under normal conditions.


·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The TCM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. Then the TCM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In the case of an open or short circuit, the TCM stops sending current to the circuit.

While driving and shifting gears, if the TCM detects an open or short in the shift solenoid valve SL2 circuit, the TCM determines there is a malfunction (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)>FAIL-SAFE CHART).

WIRING DIAGRAM

C219217
2.802,1.333 3.031,1.5 0.229,0.167 10 false 11 5.542,1.333 5.771,1.5 0.229,0.167 10 false 7 2.344,1.104 2.771,1.302 0.427,0.198 10 false SL2+ 2.813,2.552 3.042,2.719 0.229,0.167 10 false 3 0.823,2.208 1.052,2.375 0.229,0.167 10 false 2 0.823,1.417 1.052,1.583 0.229,0.167 10 false 1 2.375,2.313 2.802,2.51 0.427,0.198 10 false SL2- 5.75,1.229 6.177,1.427 0.427,0.198 10 false SL2+ 5.542,2.542 5.771,2.708 0.229,0.167 10 false 6 5.771,2.427 6.198,2.625 0.427,0.198 10 false SL2- 1.021,2.948 1.448,3.146 0.427,0.198 10 false C151 1.021,3.115 2.271,3.313 1.25,0.198 10 false Transmission Wire 1.042,1.802 2.688,2.031 1.646,0.229 10 false Shift Solenoid Valve SL2 5.958,3.271 6.302,3.438 0.344,0.167 10 false C24 5.958,3.427 6.385,3.625 0.427,0.198 10 false TCM

CAUTION / NOTICE / HINT

HINT:

Shift solenoid valve SL2 is turned ON/OFF normally when the shift lever is in D.

TCM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve SL2 ON ON ON ON OFF


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)
a.
C214326
1.854,1.323 1.635,1.75 true 1.938,1.115 2.208,1.75 true 1.479,1.792 1.844,1.958 0.365,0.167 10 false SL2+ 0.052,0.052 0.281,0.219 0.229,0.167 10 false *a 2.104,1.781 2.448,1.948 0.344,0.167 10 false SL2-
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (SL2+) - 3 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
11 (SL2+) - Body ground 20°C (68°F) 10 kΩ or higher
3 (SL2-) - Body ground 20°C (68°F) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL2
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
C212047
0.813,0.313 1.198,0.583 0.385,0.271 0.479,2.792 0.906,2 true 1.667,2.792 0.969,2 true 0.198,2.813 1.115,3.01 0.917,0.198 10 false 7 (SL2+) 1.479,2.792 2.396,2.99 0.917,0.198 10 false 6 (SL2-) 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.875,0.365 1.375,0.563 0.5,0.198 10 false C24
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-7 (SL2+) - C24-6 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
C24-7 (SL2+) - Body ground 20°C (68°F) 10 kΩ or higher
C24-6 (SL2-) - Body ground 20°C (68°F) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL2
a.
C197715C22
1.781,0.958 2.229,0.375 true 1.469,0.958 1.01,0.375 true 1.76,2.948 2.208,2.354 true 1.469,2.948 1.01,2.354 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.25,0.229 2.417,0.427 0.167,0.198 10 false 1 0.896,0.24 1.063,0.438 0.167,0.198 10 false 2 2.25,2.219 2.417,2.417 0.167,0.198 10 false 1 0.917,2.219 1.083,2.417 0.167,0.198 10 false 2 1.927,3.927 2.156,4.125 0.229,0.198 10 false (+) 1.167,3.927 1.396,4.125 0.229,0.198 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL2)


Remove shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG