Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION FLUID › from 2012.04
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052494 AUTOMATIC TRANSMISSION FLUID A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE AUTOMATIC TRANSMISSION FLUID

a.

Lift the vehicle. [*1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.

Remove the drain plug and gasket, and drain the ATF. [*2]


c.

Temporarily install the gasket and drain plug. [*3]

HINT:

Reuse the old gasket. A new gasket will be installed in step [*15].



d.
C112857
1.031,1.531 1.24,0.688 1.24,0.688 1.354,0.688 true 0.781,1.333 1.021,0.344 1.021,0.344 1.135,0.344 true 1.49,3.719 1.344,4.313 1.344,4.313 1.229,4.313 true 1.417,0.594 1.698,0.781 0.281,0.188 10 false *1 1.188,0.229 1.469,0.417 0.281,0.188 10 false *3 1.042,4.229 1.323,4.438 0.281,0.208 10 false *2
*1 Refill Plug
*2 Overflow Plug
*3 Refill Hole


Remove the refill plug and overflow plug. [*4]


e.
C283563
0.688,1.271 0.906,1.271 0.906,1.271 1.073,0.833 true 1.771,0.844 2.365,1.177 2.365,1.177 2.604,1.177 true 2.667,1.094 2.979,1.25 0.313,0.156 10 false *1 0.5,1.177 0.813,1.333 0.313,0.156 10 false *a
*1 Overflow Tube
*a Specified Fluid Level


Add fluid to the refill hole until it flows out of the overflow plug hole. [*5]

NOTICE:

Use Toyota Genuine ATF WS.



f.

Wait until the fluid flow slows and only drops come out. [*6]


g.

Temporarily install the gasket and overflow plug. [*7]

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



h.

Add fluid to the refill hole using the amount of fluid specified for removal and installation of the oil pan. [*8]

HINT:

Specified amount of fluid is 1.7 liters (1.8 US qts, 1.5 Imp. qts).



i.

Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



j.

Lower the vehicle. [*10]


k.

Start the engine. [*11]

NOTICE:

Make sure that the A/C switch is off.



l.

Slowly move the shift lever from P to S, and then change the gear from 1st to 5th. Then back to P. [*12]


m.

Allow the engine to idle for 30 seconds to warm it up. [*13]


n.

Turn the ignition switch off. [*14]


o.

Repeat steps [*1] to [*14].


p.

Repeat steps [*1] to [*2].


q.

Install a new gasket and the drain plug. [*15]

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


r.

Repeat steps [*4] to [*10].



t.

Lower the vehicle.


u.

Operation complete.