Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION WIRE › from 2012.04
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052496 TRANSMISSION WIRE A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION WIRE

a.

Coat a new O-ring with ATF and install it to the transmission wire connector.


b.

Install the transmission wire with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the transmission wire connector.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



Hide 2.CONNECT TRANSMISSION WIRE

a.
C283573
1.156,1.073 1.938,0.677 true 1.146,1.583 1.563,1.333 true 1.073,0.875 0.781,0.75 true 0.406,1.208 1.052,1.333 true 0.229,1.115 0.469,1.302 0.24,0.188 10 false *2 1.615,1.24 1.823,1.427 0.208,0.188 10 false B 1.948,0.552 2.188,0.708 0.24,0.156 10 false *1 0.646,0.656 0.854,0.844 0.208,0.188 10 false A
*1 Orange
*2 Blue


Connect the 7 connectors to the solenoid valves.


b.

Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

12 mm (0.472 in.) for bolt A

36 mm (1.42 in.) for bolt B



Hide 3.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the oil strainer.


b.

Install the oil strainer with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 4.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:

Remove the gasket and be careful not to spill oil on the contacting surfaces of the transmission case and oil pan.


a.

Install a new gasket and the oil pan with the 20 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 5.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 1KD-FTV)

a.

Install the rear No. 1 engine mounting insulator to the transmission with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 6.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for 1KD-FTV)

a.

Install the No. 3 frame crossmember to the rear No. 1 engine mounting insulator with the 4 set bolts.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


b.

Connect the ends of the No. 3 frame crossmember to the vehicle with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)