Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT › from 2012.04
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052504 AUTOMATIC TRANSMISSION UNIT A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

D027971

a.

Remove the nut, spring washer and control shaft lever LH.


Hide 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903

a.

Using a screwdriver, bend the tabs of the lock washer.


b.

Remove the nut, lock washer and bolt.


c.

Remove the park/neutral position switch.

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



Hide 3.REMOVE OIL COOLER TUBE UNION

D027989

a.

Remove the 2 oil cooler tube unions.


b.

Remove the 2 O-rings from the oil cooler tube unions.


Hide 4.REMOVE SPEED SENSOR

C111258

a.

Remove the 2 bolts and 2 speed sensors.


b.

Remove the 2 O-rings from the sensors.


Hide 5.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

C284143

a.

Remove the 3 bolts.


b.

Remove the breather tube.


c.

Remove the O-ring from the tube.


Hide 6.REMOVE AUTOMATIC TRANSMISSION HOUSING

C190068
0.083,0.073 0.396,0.292 0.313,0.219 10 false *A 0.083,2.313 0.333,2.531 0.25,0.219 10 false *B
*A for 1GR-FE
*B for 1KD-FTV


a.

Remove the 10 bolts.


b.

Remove the transmission housing.


Hide 7.REMOVE REAR ADAPTOR TRANSFER

C283889

a.

Remove the 8 bolts.


b.

Remove the transmission case adapter.

HINT:

Use a brass bar and a hammer to remove the transmission case adapter.



c.

Remove the 2 transfer case ring pins from the transmission case adapter.


Hide 8.REMOVE TRANSMISSION CASE ADAPTER REAR OIL SEAL

C284144

a.

Using a screwdriver, pry out the oil seal.

HINT:

Wrap the tip of the screwdriver with tape.


NOTICE:

Be careful not to damage the transmission case.



Hide 9.REMOVE REAR TRANS CASE ADAPTOR OIL RECEIVER

C190069

a.

Using snap ring pliers, remove the snap ring and oil receiver.


Hide 10.FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

D027911

a.

Install the transmission case to an overhaul attachment.


Hide 11.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the pan.


a.

Remove the drain plug and 20 bolts.


Hide 13.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

D012703

a.

Turn over the transmission.


b.

Remove the 4 bolts and oil strainer from the valve body.


c.

Remove the O-ring from the oil strainer.


Hide 14.REMOVE TRANSMISSION WIRE

D012704
2.01,0.198 1.156,1.427 true 1.156,0.969 2.01,0.198 2.01,0.198 2.094,0.198 true 2.146,0.104 2.385,0.271 0.24,0.167 10 false *1
*1 Temperature Sensor Clamp


a.

Remove the 2 bolts and 2 temperature sensor clamps, and disconnect the 2 ATF temperature sensors.


b.

Disconnect the 7 connectors from the solenoid valves.


c.
D027912

Remove the bolt from the case.


d.

Pull the transmission wire out of the transmission case.


e.

Remove the O-ring from the transmission wire.


Hide 15.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.

Remove the bolt, detent spring cover and detent spring.


b.
C283576

Remove the 19 bolts and valve body.


Hide 16.REMOVE TRANSMISSION CASE GASKET

D027968

a.

Remove the 3 gaskets.


Hide 17.REMOVE BRAKE DRUM GASKET

D027969

a.

Remove the 3 gaskets.


Hide 18.REMOVE CHECK BALL BODY

D027914
1.542,1.219 0.865,1.219 true 0.875,0.417 1.292,0.417 false 0.688,0.323 0.958,0.49 0.271,0.167 10 false *1 0.677,1.135 0.948,1.313 0.271,0.177 10 false *2
*1 Check Ball Body
*2 Spring


a.

Remove the check ball body and spring.


Hide 19.REMOVE C-2 ACCUMULATOR PISTON

D027915

a.

Apply compressed air to the oil hole to remove the C-2 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 and B-3 accumulator pistons may jump out.



Hide 20.REMOVE B-3 ACCUMULATOR PISTON

D027915

a.

Apply compressed air to the oil hole to remove the B-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 accumulator piston may jump out.



Hide 21.REMOVE C-3 ACCUMULATOR PISTON

D027916

a.

Apply compressed air to the oil hole to remove the C-3 accumulator piston and 2 springs.


b.

Remove the 2 O-rings from the piston.


Hide 22.REMOVE C-1 ACCUMULATOR VALVE

D027917

a.

Remove the C-1 accumulator valve and 2 springs.


Hide 23.REMOVE PARKING LOCK PAWL BRACKET

C284100

a.

Remove the 3 bolts and bracket.


Hide 24.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

D012709

a.

Disconnect the parking lock rod from the manual valve lever.


Hide 25.REMOVE PARKING LOCK PAWL SHAFT

D028846

a.

Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.


b.

Remove the E-ring from the shaft.


Hide 26.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

D027918

a.

Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.


b.
D027919

Using a pin punch and hammer, tap out the spring pin.

HINT:

Slowly drive out the spring pin so that it does not fall into the transmission case.



c.

Pull the manual valve lever shaft out through the case, and remove the manual valve lever.


Hide 27.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C284101

a.

Using a screwdriver, pry out the 2 oil seals.

HINT:

Wrap the tip of the screwdriver with tape.


NOTICE:

Be careful not to damage the transmission case.



Hide 28.REMOVE OIL PUMP ASSEMBLY

D027921

a.

Remove the 10 bolts.


b.
D027922
1.823,0.875 2.031,0.313 true 2.073,0.198 2.458,0.385 0.385,0.188 10 false SST

Using SST, remove the oil pump.

SST
09350-30020  (09350-07020)


c.
D028796

Remove the O-ring from the front oil pump.


d.
C177431

Remove the 2 thrust bearing races from the front oil pump.


Hide 29.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

D027923

a.

Remove the clutch drum and input shaft assembly from the transmission case.


b.
C177432

Remove the clutch drum thrust washer and 2 thrust needle roller bearings.


Hide 31.REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

D027994

a.

Remove the 1-way clutch and No. 2 clutch drum thrust washer from the clutch drum and input shaft assembly.


Hide 32.FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

D027995
2.396,1.688 2.625,0.948 2.625,0.948 2.719,0.948 false 1.094,1.302 0.854,0.781 0.854,0.781 0.792,0.781 false 2.771,0.854 3.063,1.052 0.292,0.198 10 false *1 0.604,0.698 0.865,0.896 0.26,0.198 10 false *2
*1 Torque Converter Clutch
*2 Oil Pump


a.

Place the oil pump onto the torque converter, and then place the clutch drum and input shaft assembly onto the oil pump.


Hide 33.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

D027996

a.

Using a screwdriver, remove the snap ring.


b.
D027997

Remove the reverse clutch hub sub-assembly, reverse clutch reaction sleeve, clutch cushion, plate reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the clutch drum.


Hide 34.REMOVE REVERSE CLUTCH REACTION SLEEVE

D027998

a.

Remove the reverse clutch reaction sleeve from the reverse clutch hub.


Hide 35.REMOVE REAR CLUTCH DISC

D027999

a.

Remove the clutch cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.


Hide 38.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

D028001

a.

Remove the forward clutch hub from the clutch drum.


b.
D028500

Remove the 2 thrust needle roller bearings from the forward clutch hub.


Hide 40.REMOVE MULTIPLE DISC CLUTCH HUB

D028502

a.

Remove the multiple disc clutch hub from the clutch drum.


b.
D028503

Remove the 2 thrust bearing races from the multiple disc clutch hub.


Hide 41.REMOVE INPUT SHAFT ASSEMBLY

D028504

a.

Remove the thrust needle roller bearing from the clutch drum.


b.
D028505

Remove the input shaft assembly from the clutch drum.


Hide 42.REMOVE INPUT SHAFT OIL SEAL RING

C284160

a.

Remove the 3 oil seal rings from the input shaft.


Hide 43.REMOVE FORWARD MULTIPLE DISC CLUTCH DISC

D028519

a.

Using a screwdriver, remove the hole snap ring.


b.
C284161

for 1GR-FE:

Remove the 2 flanges, 6 discs and 5 plates from the input shaft.


c.
C115806

for 1KD-FTV:

Remove the 2 flanges, 7 discs and 6 plates from the input shaft.


Hide 45.REMOVE NO. 1 CLUTCH BALANCER

D028521
2.063,0.542 2.323,0.219 false 2.396,0.094 2.781,0.281 0.385,0.188 10 false SST

a.

Place SST on the clutch balancer, and compress the return spring with a press.

SST
09350-30020  (09350-07040, 09350-07070)


b.

Using a snap ring expander, remove the snap ring.


c.
D028522

Remove the clutch balancer and forward clutch return spring from the input shaft assembly.


d.
D028523

Remove the O-ring from the No. 1 clutch balancer.


Hide 47.REMOVE FORWARD CLUTCH PISTON

D028524

a.

Hold the input shaft by hand and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the input shaft to remove the forward clutch piston.


b.
D028525

Remove the 2 O-rings from the forward clutch piston.


Hide 48.REMOVE REVERSE CLUTCH FLANGE

D028506

a.

Remove the reverse clutch flange from the clutch drum.


Hide 49.REMOVE DIRECT CLUTCH DISC

D028507

a.

Using a screwdriver, remove the 2 hole snap rings from the clutch drum.


b.
C162137

for 1GR-FE:

Remove the reverse clutch flange, 5 discs and 5 plates from the clutch drum.


c.
C162138

for 1KD-FTV:

Remove the reverse clutch flange, 6 discs and 6 plates from the clutch drum.


Hide 51.REMOVE NO. 3 CLUTCH BALANCER

D028509
1.698,0.896 2.469,0.583 2.469,0.583 2.25,0.938 true 2.552,0.448 2.896,0.646 0.344,0.198 10 false SST

a.

Place SST on the clutch balancer, and compress the return spring with a press.

SST
09387-00070  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


Hide 52.REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

D028510

a.

Remove the reverse clutch return spring and O-ring from the reverse clutch piston.


Hide 54.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

D028511

a.

Remove the reverse clutch piston sub-assembly from the clutch drum.


b.
D028512

Remove the O-ring from the reverse clutch piston.


c.
D028513

Remove the O-ring from the clutch drum.


Hide 55.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

D028514
1.406,1.344 0.521,1.406 0.521,1.406 1.208,0.615 true 0.198,1.385 0.542,1.583 0.344,0.198 10 false SST

a.

Place SST on the direct clutch piston, and compress the return spring with a press.

SST
09320-89010  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
D028515

Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.


d.
D028516

Remove the O-ring from the clutch drum.


e.
D028517

Remove the No. 2 clutch balancer and direct clutch return spring from the direct clutch piston.


f.
D028816

Remove the 2 O-rings from the direct clutch piston.


Hide 57.REMOVE NO. 3 BRAKE SNAP RING

D027925

a.

Using a screwdriver, remove the No. 3 brake snap ring from the case.


Hide 58.REMOVE NO. 3 BRAKE DISC

D027926

a.

Remove the flange, 4 discs, 4 plates and cushion plate from the case.


Hide 60.REMOVE 2ND BRAKE PISTON HOLE SNAP RING

C284142
0.708,0.323 1.396,0.323 true 0.365,0.25 0.698,0.469 0.333,0.219 10 true SST

a.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


Hide 61.REMOVE 1-WAY CLUTCH ASSEMBLY

D027928

a.

Remove the 1-way clutch assembly and No. 1 planetary carrier thrust washer from the case.


Hide 62.REMOVE 2ND BRAKE CYLINDER

D027929

a.

Remove the 2nd brake cylinder from the case.


Hide 63.REMOVE 2ND BRAKE PISTON

D028817
2.26,0.615 2.781,0.271 true 2.76,0.094 3.125,0.271 0.365,0.177 10 false SST

a.

Using SST and a press, compress the return spring and remove the snap ring.

SST
09351-40010  


b.
D028545

Hold the 2nd brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the 2nd brake cylinder to remove the 2nd brake piston.


c.
D028546

Remove the 2 O-rings from the 2nd brake piston.


Hide 65.REMOVE FRONT PLANETARY GEAR ASSEMBLY

D027930

a.

Remove the front planetary gear assembly and 1-way clutch inner race from the case.


b.
D027931

Remove the No. 5 thrust bearing race, thrust needle roller bearing and No. 2 planetary carrier thrust washer from the front planetary gear assembly.


Hide 68.REMOVE FRONT PLANETARY RING GEAR

D027932

a.

Remove the front planetary ring gear and thrust needle roller bearing from the transmission case.


Hide 69.REMOVE CENTER PLANETARY RING GEAR

D028540

a.

Using a screwdriver, remove the snap ring.


b.
D028541

Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.


Hide 70.REMOVE NO. 1 BRAKE DISC

D027933

a.

Remove the flange, 3 discs and 3 plates from the case.


Hide 72.REMOVE BRAKE PISTON RETURN SPRING SNAP RING

D027934

a.

Using a screwdriver, remove the brake piston return spring snap ring from the case.


Hide 73.REMOVE BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D027935

a.

Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.


Hide 75.REMOVE NO. 1 BRAKE PISTON

D027936

a.

Hold the No. 1 brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to No. 1 brake cylinder to remove the No. 1 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 1 brake piston.


Hide 76.REMOVE NO. 2 BRAKE DISC

D027937

a.

Using a screwdriver, remove the snap ring from the case.


b.
D027938

Remove the flange, 3 discs, 3 plates and brake piston return spring from the case.


Hide 79.REMOVE NO. 2 BRAKE PISTON

D027939

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transmission case to remove the No. 2 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 2 brake piston.


Hide 80.REMOVE CENTER PLANETARY GEAR ASSEMBLY

D027940

a.

Remove the No. 6 thrust bearing race, center planetary gear and planetary sun gear from the case.


Hide 82.REMOVE INTERMEDIATE SHAFT

D027941

a.

Using a screwdriver, remove the snap ring from the case.


b.
D027942

Remove the intermediate shaft with No. 3 1-way clutch assembly from the case.


Hide 84.REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY

D027964

a.

Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.


Hide 85.REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D027965

a.

Remove the planetary ring gear flange, No. 7 thrust bearing race, thrust needle roller bearing and No. 8 thrust bearing race from the intermediate shaft.


Hide 88.REMOVE BRAKE PLATE STOPPER SPRING

D027943

Hide 89.REMOVE NO. 4 BRAKE DISC

C284162

a.

Remove the 7 plates, 8 discs and 2 flanges from the case.


Hide 91.REMOVE REAR PLANETARY GEAR ASSEMBLY

C190075

a.

Remove the rear planetary gear assembly from the case.


b.
C190076

Remove the 2 thrust needle roller bearings from the rear planetary gear.


c.
C284163

Remove the No. 9 thrust bearing race from the case.


Hide 93.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D028083
2.417,1.021 2.698,0.208 2.698,0.208 2.802,0.208 true 1.49,0.75 1.448,0.26 1.448,0.26 1.344,0.26 false 2.865,0.125 3.146,0.333 0.281,0.208 10 true *1 1.021,0.177 1.375,0.375 0.354,0.198 10 false SST
*1 Snap Ring


a.

Place SST on the spring retainer and compress the brake return spring.

SST
09350-30020  (09350-07050)


b.

Using SST, remove the snap ring and brake return spring.

SST
09350-30020  (09350-07070)


Hide 94.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 95.REMOVE 1ST AND REVERSE BRAKE PISTON

D027948

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transmission case to remove the 1st and reverse brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the O-ring from the 1st and reverse brake piston.


Hide 96.REMOVE BRAKE REACTION SLEEVE

D028079
1.49,0.448 1.083,0.448 false 0.771,0.375 1.135,0.552 0.365,0.177 10 false SST

a.

Using SST, remove the reaction sleeve.

SST
09350-30020  (09350-07080)


b.

Remove the 2 O-rings from the reaction sleeve.


Hide 97.REMOVE NO. 4 BRAKE PISTON

D001240
1.25,0.302 1.552,0.531 false 0.927,0.188 1.281,0.375 0.354,0.188 10 false SST

a.

Using SST, remove the brake piston.

SST
09350-30020  (09350-07090)


b.

Remove the 2 O-rings from the brake piston.