Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P0500  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of this pulse signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor Malfunction While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the TCM (2-trip detection logic).
·

Open or short in speed signal SPD1 circuit

·

Combination meter system

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite this condition being met, the TCM interprets this as a malfunction in the speed signal circuit. The TCM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C231288
5.813,2.198 6.208,2.396 0.396,0.198 10 false TCM 5.802,2.031 6.25,2.229 0.448,0.198 10 false G41 5.615,1.313 6.042,1.51 0.427,0.198 10 false SPD1 5.365,1.427 5.615,1.625 0.25,0.198 10 false 25 2.635,1.917 3.844,2.281 1.208,0.365 10 false Combination Meter Assembly 2.635,1.74 3.083,1.938 0.448,0.198 10 false G19 2.677,1.438 2.823,1.635 0.146,0.198 10 false 5 3.688,1.427 3.938,1.625 0.25,0.198 10 false 6 0.396,1.302 2.115,1.49 1.719,0.188 10 false from Speedometer Sensor 4.271,1.74 4.563,1.938 0.292,0.198 10 false 2Q 4.104,1.427 4.354,1.625 0.25,0.198 10 false 26 4.917,1.427 5.167,1.625 0.25,0.198 10 false 10 4.26,1.906 4.969,2.271 0.708,0.365 10 false Junction Connector 3.396,1.313 3.688,1.51 0.292,0.198 10 false +S 2.885,1.323 3.177,1.521 0.292,0.198 10 false SI

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.


·

If the speedometer does not operate, check it by following the procedure described for a speedometer malfunction.




b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / ECT / Data List.


f.

Drive the vehicle.


g.

Read the value displayed on the tester.

Powertrain > ECT > Data List
Tester Display
Vehicle Speed
50003 64 315
Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
OK:

Vehicle speed displayed on the intelligent tester and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system.

Click here

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G41 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-6 (+S) - G41-25 (SPD1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - TCM)
4.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - TCM)
a.

Disconnect the 2Q junction connector.


b.

Disconnect the G41 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2Q-10 - G41-25 (SPD1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR