Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
·

NSW input signal is ON

·

R input signal is ON

·

D input signal is ON

·

3 input signal is ON

·

2 input signal is ON


(B) Any of the following signals is ON for 2.0 sec. or more with the shift lever in 4 or L (2-trip detection logic):
·

NSW input signal is ON

·

R input signal is ON

·

3 input signal is ON


(C) All switches are OFF simultaneously for NSW, R, D, 3, and 2 (2-trip detection logic).
·

Open or short in park/neutral position switch circuit

·

Shift lock control ECU (shift lock control unit assembly)

·

Park/neutral position switch assembly

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and wire harness in the park/neutral position switch circuit.

The park/neutral position switch and shift lock control ECU detects the shift lever position (R, D, 4, 3, 2, or L) and sends a signal to the TCM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The TCM determines that there is a problem with the switch or related parts if it receives more than 1 of the R, D, 3 or 2 position signals simultaneously. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C237622
5.521,0.573 5.708,0.771 0.188,0.198 10 false 12 5.813,0.74 6.188,0.938 0.375,0.198 10 false NSW 5.448,0.75 5.75,0.948 0.302,0.198 10 false C24 5.552,1.74 5.74,1.938 0.188,0.198 10 false 9 5.823,1.917 6.198,2.115 0.375,0.198 10 false R 5.448,1.927 5.75,2.125 0.302,0.198 10 false G40 5.552,2.354 5.729,2.552 0.177,0.198 10 false 8 5.813,2.5 6.188,2.698 0.375,0.198 10 false D 5.448,2.521 5.75,2.719 0.302,0.198 10 false G40 5.51,2.938 5.698,3.135 0.188,0.198 10 false 12 5.823,3.115 6.198,3.313 0.375,0.198 10 false 3 5.448,3.125 5.75,3.323 0.302,0.198 10 false G40 5.51,3.521 5.698,3.719 0.188,0.198 10 false 11 5.823,3.708 6.198,3.906 0.375,0.198 10 false 2 5.448,3.719 5.75,3.917 0.302,0.198 10 false G40 5.51,5.635 5.708,5.833 0.198,0.198 10 false 13 5.823,5.823 6.198,6.021 0.375,0.198 10 false 4 5.448,5.823 5.75,6.021 0.302,0.198 10 false G40 5.521,6.146 5.708,6.344 0.188,0.198 10 false 10 5.823,6.323 6.198,6.521 0.375,0.198 10 false L 5.448,6.323 5.75,6.521 0.302,0.198 10 false G40 5.552,6.646 5.688,6.844 0.135,0.198 10 false 1 5.813,6.823 6.188,7.021 0.375,0.198 10 false E1 5.448,6.833 5.75,7.031 0.302,0.198 10 false C24 3.948,1.385 4.094,1.583 0.146,0.198 10 false L 2.833,1.385 2.979,1.583 0.146,0.198 10 false B 3.844,1.813 4.052,2.01 0.208,0.198 10 false RL 3.844,2.406 4.052,2.604 0.208,0.198 10 false DL 3.865,3.01 4.073,3.208 0.208,0.198 10 false 2L 3.865,3.625 4.073,3.823 0.208,0.198 10 false LL 4.146,1.583 4.313,1.781 0.167,0.198 10 false 5 4.146,2.031 4.313,2.229 0.167,0.198 10 false 1 4.146,2.635 4.313,2.833 0.167,0.198 10 false 7 4.146,3.229 4.313,3.427 0.167,0.198 10 false 3 4.146,3.823 4.313,4.021 0.167,0.198 10 false 8 2.833,2.729 3.083,2.927 0.25,0.198 10 false RB 2.635,1.583 2.802,1.781 0.167,0.198 10 false 4 2.635,2.948 2.802,3.146 0.167,0.198 10 false 2 6.115,7.385 6.49,7.583 0.375,0.198 10 false TCM 2.563,4.24 2.865,4.438 0.302,0.198 10 false C57 2.563,4.417 4.396,4.615 1.833,0.198 10 false Park/Neutral Position Switch 2.708,6.802 3,7 0.292,0.198 10 false G37 2.708,6.979 4.542,7.177 1.833,0.198 10 false Shift Lock Control ECU 4.667,1.479 5.469,1.677 0.802,0.198 10 false to ST Relay 1.115,1.479 2.031,1.677 0.917,0.198 10 false from ST Fuse 0.229,2.823 2.052,3.021 1.823,0.198 10 false from ECU-IG&GAUGE Fuse 3.781,5.719 4.094,5.917 0.313,0.198 10 false AT4 4.146,5.927 4.354,6.125 0.208,0.198 10 false 3 3.781,6.229 4.063,6.427 0.281,0.198 10 false ATL 4.156,6.438 4.365,6.635 0.208,0.198 10 false 4 2.833,6.219 3.25,6.417 0.417,0.198 10 false NSSL 2.833,5.719 3.281,5.917 0.448,0.198 10 false NSSD 2.625,5.927 2.771,6.125 0.146,0.198 10 false 9 2.563,6.438 2.771,6.635 0.208,0.198 10 false 10

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / ECT / Data List.


f.

According to the display on the tester, read the Data List.

Powertrain > ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (R Range)
Shift SW Status (2 Range)
Shift SW Status (L Range)
Shift SW Status (D Range)
Shift SW Status (4 or D)
Shift SW Status (3 Range)
50003 64 206,166,164,162,167,165,163
Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (2 Range) PNP switch status ON or OFF
·

ON: Shift lever in 2 or L

·

OFF: Shift lever not in 2 or L


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (L Range) PNP switch status ON or OFF
·

ON: Shift lever in L

·

OFF: Shift lever not in L


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever in D

·

OFF: Shift lever not in D


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (4 or D) PNP switch status ON or OFF
·

ON: Shift lever in 4 or D

·

OFF: Shift lever not in 4 or D


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (3 Range) PNP switch status ON or OFF
·

ON: Shift lever in 3

·

OFF: Shift lever not in 3


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU-IG&GAUGE FUSE - PARK/NEUTRAL POSITION SWITCH)
a.
C253110
0.406,1 0.823,1.271 0.417,0.271 1.781,0.99 1.99,0.385 true 2.073,0.302 2.313,0.49 0.24,0.188 10 false RB 0.49,1.052 0.948,1.25 0.458,0.198 10 false C57 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
C57-2 (RB) - Body ground Ignition switch ON 11 to 14 V
C57-2 (RB) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
C253110
0.406,1 0.823,1.271 0.417,0.271 2.063,1 2.271,0.396 true 2.333,0.313 2.49,0.51 0.156,0.198 10 false B 0.479,1.052 0.938,1.25 0.458,0.198 10 false C57 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the G39 ECM connector.


b.

Disconnect the park/neutral position switch connector.


c.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
C57-4 (B) - Body ground Ignition switch ON 11 to 14 V
C57-4 (B) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712
1.292,1.708 1.458,1.281 true 1.688,1.698 1.708,1.271 true 1.583,0.948 1.719,0.51 true 1.396,0.958 1.271,0.531 true 0.958,0.531 1.271,0.948 true 2.448,1.688 2.083,1.281 true 1.844,0.948 2.24,0.521 true 1.198,1.75 1.438,1.99 0.24,0.24 10 false LL 0.823,0.375 1.01,0.615 0.188,0.24 10 false B 1.615,1.74 1.969,1.969 0.354,0.229 10 false DL 2.479,1.729 2.667,1.969 0.188,0.24 10 false L 1.188,0.344 1.479,0.563 0.292,0.219 10 false 2L 1.646,0.344 2,0.583 0.354,0.24 10 false RB 2.167,0.344 2.552,0.583 0.385,0.24 10 false RL 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
2 (RB) - 7 (DL) Shift lever in D or 4 Below 1 Ω
2 (RB) - 3 (2L) Shift lever in 3 Below 1 Ω
2 (RB) - 8 (LL) Shift lever in 2 or L Below 1 Ω
4 (B) - 5 (L) Shift lever not in P or N 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever not in D or 4 10 kΩ or higher
2 (RB) - 3 (2L) Shift lever not in 3 10 kΩ or higher
2 (RB) - 8 (LL) Shift lever not in 2 or L 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

4.INSPECT SHIFT LOCK CONTROL ECU

NG

4.INSPECT SHIFT LOCK CONTROL ECU
a.
C214966
1.25,1.656 1.646,1.26 true 1.656,0.948 1.313,0.448 true 1.76,0.948 2.073,0.458 true 1.802,1.25 2.156,1.656 true 1.177,0.26 1.792,0.458 0.615,0.198 10 false ATL 1.01,1.677 1.625,1.875 0.615,0.198 10 false NSSL 1.99,1.677 2.604,1.875 0.615,0.198 10 false NSSD 1.979,0.26 2.594,0.458 0.615,0.198 10 false AT4 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a
*a Component without harness connected
(Shift Lock Control ECU)


Disconnect the shift lock control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (NSSD) - 3 (AT4) Shift lever in D 10 kΩ or higher
Shift lever in 4 Below 1 Ω
10 (NSSL) - 4 (ATL) Shift lever in 2 10 kΩ or higher
Shift lever in L Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)

NG

REPLACE SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)
a.
C203405
0.594,0.896 1.021,1.146 0.427,0.25 1.26,1.677 1.635,1.313 true 2.115,1.667 1.813,1.313 true 1.01,1.688 1.667,1.865 0.656,0.177 10 false NSSD 2,1.688 2.656,1.865 0.656,0.177 10 false NSSL 0.667,0.938 1.125,1.135 0.458,0.198 10 false G37 0.063,0.083 0.375,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Disconnect the shift lock control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G37-9 (NSSD) - Body ground
·

Ignition switch ON

·

Shift lever in D or 4


11 to 14 V
G37-9 (NSSD) - Body ground
·

Ignition switch ON

·

Shift lever not in D or 4


Below 1 V
G37-10 (NSSL) - Body ground
·

Ignition switch ON

·

Shift lever in 2 or L


11 to 14 V
G37-10 (NSSL) - Body ground
·

Ignition switch ON

·

Shift lever not in 2 or L


Below 1 V


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.
C212050
0.781,0.76 1.229,1.021 0.448,0.26 1.531,0.76 2,1.031 0.469,0.271 0.344,2.302 1.313,1.521 true 1.042,2.333 1.635,1.646 true 2.156,2.698 1.833,1.635 true 2.281,2.344 1.906,1.625 true 1.208,2.698 1.698,1.646 true 1.667,2.365 1.771,1.635 true 2.969,2.698 1.958,1.625 true 0.073,2.344 0.99,2.542 0.917,0.198 10 false 1 (E1) 0.802,2.344 1.719,2.542 0.917,0.198 10 false 13 (4) 2.865,2.719 3.292,2.938 0.427,0.219 10 false 8 (D) 1.021,2.719 1.938,2.917 0.917,0.198 10 false 12 (3) 1.5,2.344 2.417,2.542 0.917,0.198 10 false 11 (2) 2.219,2.354 3.135,2.552 0.917,0.198 10 false 9 (R) 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 0.875,0.813 1.792,1.01 0.917,0.198 10 false C24 1.646,0.813 2.563,1.01 0.917,0.198 10 false G40 2,2.719 2.917,2.917 0.917,0.198 10 false 10 (L)
*a Component with harness connected
(TCM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G40-9 (R) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
G40-8 (D) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever in D or 4


11 to 14 V
G40-13 (4) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever in 4


11 to 14 V
G40-12 (3) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever in 3


11 to 14 V
G40-11 (2) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever in 2 or L


11 to 14 V
G40-10 (L) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever in L


11 to 14 V
G40-9 (R) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
G40-8 (D) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever not in D or 4


Below 1 V
G40-13 (4) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever not in 4


Below 1 V
G40-12 (3) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever not in 3


Below 1 V
G40-11 (2) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever not in 2 or L


Below 1 V
G40-10 (L) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever not in L


Below 1 V


HINT:

*: The voltage will drop slightly due to illumination of the back-up light.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.

Disconnect the C24 TCM connector.


b.

Disconnect the C57 park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-12 (NSW) - C57-4 (B) Always Below 1 Ω
C24-12 (NSW) - Body ground Always 10 kΩ or higher
C57-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR