Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P0973  Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)  P0974  Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the TCM. If an open or short circuit occurs in one of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly. In the case of an open or short circuit, the TCM stops sending current to the circuit. For details, refer to the fail-safe chart (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)>FAIL-SAFE CHART).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0973 Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1) TCM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip detection logic).
·

Short in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

TCM


Comes on DTC stored
P0974 Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1) TCM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip detection logic).
·

Open in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S1 is on, if its resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve S1 circuit.

When shift solenoid valve S1 is off, if its resistance is 100 kΩ or higher, the TCM determines there is an open in the shift solenoid valve S1 circuit (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)>FAIL-SAFE CHART).

WIRING DIAGRAM

C219218
5.729,1 6.125,1.188 0.396,0.188 10 false S1 5.927,3.26 6.323,3.448 0.396,0.188 10 false TCM 5.917,3.104 6.313,3.292 0.396,0.188 10 false C24 2.5,0.896 2.688,1.083 0.188,0.188 10 false S1 2.792,1.125 2.927,1.313 0.135,0.188 10 false 8 5.469,1.125 5.667,1.313 0.198,0.188 10 false 18 1.021,1.75 2.552,1.938 1.531,0.188 10 false Shift Solenoid Valve S1 0.938,2.979 2.26,3.167 1.323,0.188 10 false Transmission Wire 0.938,2.813 1.365,3 0.427,0.188 10 false C151

CAUTION / NOTICE / HINT

HINT:

Shift solenoid valve S1 is turned ON/OFF normally when the shift lever is in D.

TCM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve S1 ON ON OFF OFF OFF


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1)
a.
C214326
1.198,1.104 0.958,1.75 true 0.052,0.021 0.281,0.188 0.229,0.167 10 false *a 0.844,1.771 1.083,1.938 0.24,0.167 10 false S1
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (S1) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE S1
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
C212047
0.813,0.313 1.198,0.583 0.385,0.271 0.75,2.792 0.906,2.073 true 0.552,2.813 1.469,3.01 0.917,0.198 10 false 18 (S1) 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.875,0.365 1.375,0.563 0.5,0.198 10 false C24
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-18 (S1) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE S1
a.
C214327
0.052,0.042 0.281,0.188 0.229,0.146 10 false *a 2.479,0.271 2.719,0.49 0.24,0.219 10 false (+) 3.177,0.26 3.344,0.51 0.167,0.25 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve S1)


Remove shift solenoid valve S1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S1 connector

·

Battery negative (-) → Shift solenoid valve S1 body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG