Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The amount of current flow to the solenoid is controlled by the current of the TCM output signal. During the lock-up operation, if the current increases, the lock-up hydraulic pressure increases.

C261110E05
4.74,2.052 5.052,1.146 5.052,1.146 5.115,1.146 true 4.948,2.219 5.083,2.625 5.083,2.625 5.156,2.625 true 5.729,2.313 5.833,2.625 5.833,2.625 5.896,2.625 true 5.948,2.542 6.833,2.76 0.885,0.219 10 false Solenoid Coil 0.042,0.552 1.292,0.771 1.25,0.219 10 false Hydraulic Pressure 2.521,2.938 3.083,3.156 0.563,0.219 10 false Current 5.198,2.531 5.729,2.75 0.531,0.219 10 false Sleeve 5.167,1.052 6,1.271 0.833,0.219 10 false Spool Valve

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) Open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLU circuit is detected, the TCM determines there is a malfunction. The TCM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C219217
2.802,1.344 3.031,1.51 0.229,0.167 10 false 13 5.458,1.333 5.688,1.5 0.229,0.167 10 false 22 2.323,1.104 2.75,1.302 0.427,0.198 10 false SLU+ 2.813,2.542 3.042,2.708 0.229,0.167 10 false 5 0.813,2.208 1.042,2.375 0.229,0.167 10 false 1 0.813,1.406 1.042,1.573 0.229,0.167 10 false 2 2.344,2.323 2.771,2.521 0.427,0.198 10 false SLU- 5.771,1.24 6.198,1.438 0.427,0.198 10 false SLU+ 5.479,2.563 5.708,2.729 0.229,0.167 10 false 21 5.781,2.438 6.208,2.635 0.427,0.198 10 false SLU- 1.021,2.958 1.448,3.156 0.427,0.198 10 false C151 1.031,3.135 2.281,3.333 1.25,0.198 10 false Transmission Wire 1.052,1.802 2.698,2.031 1.646,0.229 10 false Shift Solenoid Valve SLU 5.958,3.25 6.302,3.417 0.344,0.167 10 false C24 5.969,3.406 6.396,3.604 0.427,0.198 10 false TCM

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C214326
1.573,1.302 1.385,1.729 true 1.646,1.104 1.906,1.75 true 1.177,1.781 1.583,1.948 0.406,0.167 10 false SLU+ 0.052,0.021 0.281,0.188 0.229,0.167 10 false *a 1.771,1.781 2.146,1.948 0.375,0.167 10 false SLU-
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLU+) - 5 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLU+) - Body ground Always 10 kΩ or higher
5 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
C212047
0.813,0.313 1.198,0.583 0.385,0.271 0.385,2.781 0.656,2.073 true 1.25,2.802 0.719,2.063 true 0.156,2.823 1.073,3.021 0.917,0.198 10 false 22 (SLU+) 1.083,2.823 2,3.021 0.917,0.198 10 false 21 (SLU-) 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.875,0.365 1.375,0.563 0.5,0.198 10 false C24
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-22 (SLU+) - C24-21 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C24-22 (SLU+) - Body ground Always 10 kΩ or higher
C24-21 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLU
a.
C209928
1.771,0.969 2.219,0.385 true 1.469,0.969 1.01,0.385 true 1.76,2.948 2.208,2.354 true 1.458,2.948 1,2.354 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.26,0.271 2.427,0.469 0.167,0.198 10 false 1 0.896,0.26 1.063,0.458 0.167,0.198 10 false 2 2.24,2.24 2.406,2.438 0.167,0.198 10 false 1 0.885,2.25 1.052,2.448 0.167,0.198 10 false 2 1.927,3.958 2.125,4.156 0.198,0.198 10 false (-) 1.115,3.969 1.333,4.167 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLU)


Remove shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG