Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P0560  System Voltage  


DESCRIPTION

The battery supplies power to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the TCM data is cleared and the TCM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the TCM will illuminate the MIL and store the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage Open in the TCM back-up power source circuit (1-trip detection logic).
·

Open in back-up power source circuit

·

TCM


Comes on DTC stored

HINT:

If DTC P0560 is stored, the TCM does not store other DTCs.


WIRING DIAGRAM

C156221
5.521,1.031 5.823,1.198 0.302,0.167 10 false G41 5.615,0.854 5.844,1.021 0.229,0.167 10 false 5 5.896,1.031 6.323,1.229 0.427,0.198 10 false BATT 0.896,1.031 1.823,1.229 0.927,0.198 10 false from Battery 4.323,1.188 4.625,1.385 0.302,0.198 10 false EFI 5.531,2.083 5.813,2.25 0.281,0.167 10 false C24 5.615,1.906 5.844,2.073 0.229,0.167 10 false 1 5.896,2.094 6.323,2.292 0.427,0.198 10 false E1 6.083,2.802 6.51,3 0.427,0.198 10 false TCM 2.917,1.198 3.646,1.396 0.729,0.198 10 false BATT P/I

PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM DTC P0560)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs using the tester.

Result:
Result Proceed to
DTCs are not output A
P0560 is output (ECD system) B




A

2.CHECK TCM (BATTERY, GROUND)

B

2.CHECK TCM (BATTERY, GROUND)
a.
C216560
0.823,0.385 1.26,0.646 0.438,0.26 2.271,0.385 2.708,0.646 0.438,0.26 1.313,1.948 1.448,2.875 true 2.281,1.948 2.198,2.885 true 0.917,0.438 1.198,0.594 0.281,0.156 10 false C24 2.354,0.438 2.646,0.594 0.292,0.156 10 false G41 0.052,0.021 0.25,0.198 0.198,0.177 10 false *a 1.26,2.917 1.698,3.188 0.438,0.271 10 false 1 (E1) 1.969,2.917 2.604,3.167 0.635,0.25 10 false 5 (BATT)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G41-5 (BATT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TCM - BATTERY, GROUND)