Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.

If the TCM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at more than 20 km/h (12.4 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High All conditions are met (1-trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is ON.
(d) Battery voltage (10.5 V or higher) is applied to the TCM for 20 seconds.
·

Park/neutral position switch assembly

·

Starter relay circuit

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C229622
5.792,5.177 6.177,5.406 0.385,0.229 9 false TCM 3.458,4.083 5.448,4.281 1.99,0.198 9 false Park/Neutral Position Switch 3.458,3.917 3.885,4.146 0.427,0.229 9 false C57 5.302,2 5.51,2.177 0.208,0.177 9 false 12 5.333,2.563 5.49,2.74 0.156,0.177 9 false 8 5.323,3.115 5.458,3.292 0.135,0.177 9 false 9 5.323,4.417 5.458,4.594 0.135,0.177 9 false 1 4.885,2.26 5.094,2.469 0.208,0.208 9 false 4 3.719,2.271 3.927,2.479 0.208,0.208 9 false 5 2.521,1.719 2.729,1.927 0.208,0.208 9 false 3 3.302,1.729 3.51,1.938 0.208,0.208 9 false 5 2.521,2.26 2.729,2.469 0.208,0.208 9 false 2 3.313,2.25 3.521,2.458 0.208,0.208 9 false 1 3.719,3.115 3.927,3.323 0.208,0.208 9 false 2 4.885,2.833 5.094,3.042 0.208,0.208 9 false 7 4.875,3.406 5.083,3.615 0.208,0.208 9 false 1 2.865,2.51 3.156,2.75 0.292,0.24 9 false ST 5.583,0.677 5.927,0.854 0.344,0.177 9 false STA 5.25,0.667 5.594,0.844 0.344,0.177 9 false C24 5.25,2.167 5.594,2.344 0.344,0.177 9 false C24 5.24,2.719 5.583,2.896 0.344,0.177 9 false G40 5.25,3.281 5.594,3.458 0.344,0.177 9 false G40 5.25,4.594 5.594,4.771 0.344,0.177 9 false C24 5.292,0.5 5.5,0.656 0.208,0.156 9 false 11 1.479,1.635 2.281,1.917 0.802,0.281 9 false to Starter 0.438,3 2.406,3.219 1.969,0.219 9 false from ECU-IG&GAUGE Fuse 1.073,0.646 2.115,0.833 1.042,0.188 10 false from AM2 Fuse 4.708,2.094 4.927,2.323 0.219,0.229 9 false B 3.885,2.073 4.104,2.302 0.219,0.229 9 false L 3.885,2.906 4.104,3.135 0.219,0.229 9 false RB 4.635,2.646 4.854,2.875 0.219,0.229 9 false DL 4.625,3.208 4.844,3.438 0.219,0.229 9 false RL 5.604,2.167 5.99,2.354 0.385,0.188 9 false NSW 5.604,2.74 6.01,2.927 0.406,0.188 9 false D 5.594,3.281 5.865,3.458 0.271,0.177 9 false R 5.594,4.583 5.802,4.75 0.208,0.167 9 false E1

CAUTION / NOTICE / HINT

HINT:

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally. If the engine does not crank, proceed to the problem symptoms table.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Read the value displayed on the tester.


f.

Crank the engine.


g.

Read the value displayed on the tester.

Powertrain > ECT > Data List
Tester Display
Starter Signal
50003 64 209
Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Signal Starter signal ON or OFF
·

ON: Engine cranking

·

OFF: Engine not cranking


-
OK:

Starter Signal is only ON when the engine is being started (during cranking).



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TCM (STA VOLTAGE)
2.CHECK TCM (STA VOLTAGE)
a.
C212047
0.813,0.313 1.198,0.583 0.385,0.271 0.917,2.844 1.313,1.958 true 1.708,2.833 1.354,2.073 true 0.708,2.875 1.625,3.073 0.917,0.198 10 false 1 (E1) 1.458,2.875 2.375,3.073 0.917,0.198 10 false 11 (STA) 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.875,0.365 1.375,0.563 0.5,0.198 10 false C24
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C24-11 (STA) - C24-1 (E1)
·

Ignition switch ON

·

Shift lever in P or N


Below 2 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712
1.26,0.958 0.917,0.365 true 2.083,1.281 2.427,1.781 true 1.583,0.969 1.51,0.354 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.792,0.281 1.104,0.479 0.313,0.198 10 false B 2.479,1.719 2.792,1.917 0.313,0.198 10 false L 1.292,0.26 1.604,0.458 0.313,0.198 10 false RB
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P Below 1 Ω
4 (B) - 5 (L) Shift lever in N Below 1 Ω
4 (B) - 5 (L) Shift lever not in P 10 kΩ or higher
4 (B) - 5 (L) Shift lever not in N 10 kΩ or higher
2 (RB) - 5 (L) Shift lever in P, R, N, D, 4, 3, 2 or L 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG