Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P0818  Driveline Disconnect Switch Input Circuit  


DESCRIPTION

The TCM detects the signal from the No. 2 transfer indicator switch (the transfer neutral position switch).

This DTC indicates that the No. 2 transfer indicator switch remains on.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0818 Driveline Disconnect Switch Input Circuit The No. 2 transfer indicator switch remains on while the vehicle is being driven under the following conditions for 30 seconds (2-trip detection logic):
·

Vehicle speed is 25.1 km/h (15.6 mph) or more.

·

Transfer shift lever position: H.


·

Short in No. 2 transfer indicator switch (the transfer neutral position switch) circuit

·

No. 2 transfer indicator switch

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM detects whether or not the transfer shift lever is in neutral by monitoring the signal from the No. 2 transfer indicator switch.

If the TCM detects that the transfer shift lever is in neutral under the following conditions, the TCM will conclude that there is a malfunction of the No. 2 transfer indicator switch:

·

No. 2 transfer indicator switch indicates that the transfer shift lever is in neutral.

·

Transfer shift lever is in the H position.

·

The vehicle is traveling at 25.1 km/h (15.6 mph) or more.

·

The No. 2 transfer indicator switch has been on for more than 30 seconds.


If all of the above conditions are detected, the TCM will conclude that there is a malfunction of the No. 2 transfer indicator switch, illuminate the MIL and store the DTC.

WIRING DIAGRAM

C154998
6.104,2.979 6.625,3.188 0.521,0.208 10 false TCM 5.927,1.313 6.448,1.521 0.521,0.208 10 false TFN 5.635,1.438 5.938,1.646 0.302,0.208 10 false 16 3.646,1.417 3.802,1.625 0.156,0.208 10 false 1 2.875,1.417 3.063,1.625 0.188,0.208 10 false 2 6.094,2.792 6.615,3 0.521,0.208 10 false G40 2.323,1.615 2.844,1.823 0.521,0.208 10 false C30 2.323,1.813 4.563,2.188 2.24,0.375 10 false No. 2 Transfer Indicator Switch (Transfer neutral position switch)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - BODY GROUND)
a.
C237850
0.344,0.958 0.813,1.219 0.469,0.26 0.458,1 0.802,1.188 0.344,0.188 10 false C30 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 2 Transfer Indicator Switch)


Disconnect the No. 2 transfer indicator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 2 TRANSFER INDICATOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 2 TRANSFER INDICATOR SWITCH
a.
C237864
0.052,0 0.229,0.198 0.177,0.198 10 false *a 0.25,2.813 0.427,3.01 0.177,0.198 10 false *c 0.969,2.813 1.146,3.01 0.177,0.198 10 false *b
*a Component without harness connected
(No. 2 Transfer Indicator Switch)
*b Pushed
*c Not pushed


Remove the No. 2 transfer indicator switch.

Click hereDrivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER INDICATOR SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
1 - 2 Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - TCM)

NG

REPLACE NO. 2 TRANSFER INDICATOR SWITCH

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - TCM)
a.

Disconnect the C30 No. 2 transfer indicator switch connector.


b.

Disconnect the G40 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-1 - G40-16 (TFN) Always Below 1 Ω
C30-1 or G40-16 (TFN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR