Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The TCM detects the signal from the No. 1 transfer indicator switch (the transfer L4 position switch).

This DTC indicates that the No. 1 transfer indicator switch remains on.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance The No. 1 transfer indicator switch remains on while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
·

Output shaft speed is between 750 and 3000 rpm.

·

Transfer shift lever position is in H.


·

Short in No. 1 transfer indicator switch (the transfer L4 position switch) circuit

·

No. 1 transfer indicator switch

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM monitors the No. 1 transfer indicator switch to determine when the transfer-case L4 gear is engaged. If the transfer-case L4 gears remain engaged under all of the following conditions, the TCM will conclude that there is a malfunction of the No. 1 transfer indicator switch:

·

The No. 1 transfer indicator switch indicates that the L4 transfer-case gears are engaged.

·

Transfer-case shift lever is in the "H" position.

·

Transfer-case output shaft rpm is between 750 and 3000 rpm.

·

The specified time period has elapsed.


Then the TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C175018E19
5.708,2.896 6.042,3.094 0.333,0.198 10 false G40 5.719,3.073 6.271,3.271 0.552,0.198 10 false TCM 5.219,1.51 5.438,1.708 0.219,0.198 10 false 15 2.458,1.719 2.833,1.917 0.375,0.198 10 false C29 3.729,1.49 3.948,1.688 0.219,0.198 10 false 1 2.948,1.5 3.104,1.698 0.156,0.198 10 false 2 2.458,1.906 4.333,2.354 1.875,0.448 10 false No. 1 Transfer Indicator Switch (Transfer L4 Position Switch) 5.521,1.385 5.74,1.583 0.219,0.198 10 false L4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - BODY GROUND)
a.
C237849C03
0.323,0.938 0.76,1.198 0.438,0.26 0.083,0.01 0.354,0.219 0.271,0.208 10 false *a 0.427,0.979 0.708,1.177 0.281,0.198 10 false C29
*a Front view of wire harness connector
(to No. 1 Transfer Indicator Switch)


Disconnect the No. 1 transfer indicator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 1 TRANSFER INDICATOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 1 TRANSFER INDICATOR SWITCH
a.
C237865C04
0.052,0 0.229,0.198 0.177,0.198 10 false *a 0.24,2.917 0.417,3.115 0.177,0.198 10 false *c 0.979,2.917 1.156,3.115 0.177,0.198 10 false *b
*a Component without harness connected
(No. 1 Transfer Indicator Switch)
*b Pushed
*c Not pushed


Remove the No. 1 transfer indicator switch.

Click hereDrivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER INDICATOR SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
1 - 2 Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH -TCM)

NG

REPLACE NO. 1 TRANSFER INDICATOR SWITCH

3.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH -TCM)
a.

Disconnect the C29 No. 1 transfer indicator switch connector.


b.

Disconnect the G40 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-1 - G40-15 (L4) Always Below 1 Ω
C29-1 or G40-15 (L4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR