Home › Drivetrain › R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT › from 2012.10
RM1840EF _52 Drivetrain _009614 R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE _0052522 OUTPUT SHAFT A

R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 7.REMOVE 1ST GEAR

D026050
2.198,0.656 2.042,1.115 false 2.094,0.479 2.458,0.677 0.365,0.198 10 false SST

a.

Using SST and a press, press out the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.

SST
09950-00020  


Hide 8.REMOVE NO. 1 SYNCHRONIZER RING (FOR 1ST GEAR) (for TR Series Engine)

a.
D026051

Remove synchronizer ring (for 1st gear) from the output shaft.


Hide 9.REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR) (for 1KD-FTV, 2KD-FTV)

a.
D029120

Remove synchronizer ring (for 1st gear) from the output shaft.


Hide 10.REMOVE 1ST GEAR THRUST WASHER PIN

a.
C281933

Remove the thrust washer pin from the output shaft.


Hide 11.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

a.
D026053

Remove the needle roller bearing from the output shaft.


Hide 12.REMOVE 1ST GEAR BEARING SPACER

a.
D026054

Remove the bearing spacer from the output shaft.


Hide 13.REMOVE BEARING SHAFT SNAP RING

a.
D026055

Using 2 screwdrivers and a hammer, tap the snap ring from the output shaft.

NOTICE:

Use a cloth to prevent the snap ring from flying off.



Hide 14.REMOVE 2ND GEAR

a.
D026056
2.188,0.906 2.375,0.438 false 2.24,0.219 2.594,0.417 0.354,0.198 10 false SST

Using SST and a press, press out the No. 1 transmission clutch hub together with the reverse gear, No. 1 synchronizer ring set (for 2nd gear) and 2nd gear from the output shaft.

SST
09950-00020  


Hide 15.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.
D026057

Remove the needle roller bearing from the output shaft.


Hide 16.REMOVE REVERSE GEAR

a.
D026058

Remove the reverse gear, 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs.

NOTICE:

Use a cloth to prevent the shifting key and the shifting key springs from popping out.



Hide 17.REMOVE CLUTCH HUB SET SHAFT SNAP RING

a.
D026059

Using a snap ring expander, remove the snap ring from the output shaft.

NOTICE:

Do not damage the sliding surface of the bearing.



Hide 18.REMOVE 3RD GEAR

a.
D026060
2.49,0.479 2.208,0.865 false 2.365,0.281 2.677,0.479 0.313,0.198 10 false SST

Using SST and a press, press out the No. 2 transmission clutch hub together with the No. 2 transmission hub sleeve, No. 2 synchronizer ring and 3rd gear from the output shaft.

SST
09950-00020  


Hide 19.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.
D026061

Remove the needle roller bearing from the output shaft.


Hide 20.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.
D033571

Remove the No. 2 hub sleeve, 3 No. 2 synchromesh shifting key springs and 3 No. 2 synchromesh shifting keys from the No. 2 clutch hub.