Home › Drivetrain › VF2A TRANSFER / 4WD / AWD › TRANSFER SYSTEM
RM1840EF _52 Drivetrain _009616 VF2A TRANSFER / 4WD / AWD _0052535 TRANSFER SYSTEM G

VF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1. TRANSFER SYSTEM

NOTICE:
·

To shift from H2 to H4, reduce the vehicle speed to less than 80 km/h (50 mph) and move the transfer shift lever.

·

A/T:

To shift from H4 to L4, stop the vehicle, move the shift lever to N, and then move the transfer shift lever.

·

A/T:

To shift from L4 to H4, stop the vehicle, move the shift lever to N, and then move the transfer shift lever.

·

M/T:

To shift from H4 to L4, stop the vehicle or reduce the vehicle speed to less than 5 km/h (3 mph). Then, release the accelerator pedal, depress the clutch pedal and move the transfer shift lever.

·

M/T:

To shift from L4 to H4, depress the clutch pedal and move the transfer shift lever.



Hide 2.CHECK H2 (2WD) - H4 OR L4 (4WD) SHIFT

a.

Start the engine.


b.
G100315
2.575,2.756 2.804,2.944 0.229,0.188 10 *2 1.083,2.756 1.325,2.957 0.242,0.201 10 *1
*1 Transfer Shift Lever
*2 4WD Indicator Light


Move the transfer shift lever from the H2 position to the H4 or L4 position.


c.

Check that the 4WD indicator light illuminates.


d.

Move the transfer shift lever from the H4 or L4 position to the H2 position.


e.

Check that the 4WD indicator light turns off.

HINT:
·

If the indicator light does not turn off when you move the transfer shift lever to H2, drive straight ahead while accelerating or decelerating, or drive in reverse.

·

If a shift is uncompleted for 30 minutes, the 4WD indicator light will begin flashing.




Hide 3.CHECK 4WD CONTROL ECU

a.
C237900
0.073,0.792 0.406,1.031 0.333,0.24 2.219,1.104 2.646,0.375 true 2.052,1.104 2.24,0.375 true 1.333,1.094 0.958,0.375 true 1.49,1.083 1.365,0.375 true 2.229,1.365 2.615,1.531 true 1.25,1.365 0.844,1.625 true 2.042,1.365 2.469,1.833 true 1.698,1.365 1.323,1.833 true 1.865,1.344 2.073,1.813 true 0.115,0.833 0.396,1.021 0.281,0.188 10 true F14 0.677,0.177 1.063,0.354 0.385,0.177 10 false DM1 1.177,0.177 1.563,0.344 0.385,0.167 10 false DM2 2.625,0.177 2.948,0.344 0.323,0.167 10 false DL1 2.083,0.177 2.438,0.344 0.354,0.167 10 false DL2 0.667,1.542 0.906,1.698 0.24,0.156 10 false IG 1.052,1.865 1.396,2.021 0.344,0.156 10 false ADD 1.958,1.865 2.323,2.031 0.365,0.167 10 false IND1 2.427,1.865 2.677,2.031 0.25,0.167 10 false DL 2.646,1.49 3.01,1.656 0.365,0.167 10 false GND

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage and Resistance:
Tester Connection Condition Specified Condition
F14-10 (IG) - F14-5 (GND) Ignition switch ON 10 to 14 V
F14-7 (IND1) - F14-5 (GND) Ignition switch ON and transfer shift lever position H2 10 to 14 V
F14-7 (IND1) - F14-5 (GND) Ignition switch ON and transfer shift lever position H4 or L4 0 to 3.5 V
F14-8 (ADD) - F14-5 (GND) Ignition switch ON and A.D.D. not locked 10 to 14 V
F14-8 (ADD) - F14-5 (GND) Ignition switch ON and A.D.D. locked Below 1.5 V
F14-6 (4WD) - F14-5 (GND) Ignition switch ON and transfer shift lever position H2 10 to 14 V
F14-6 (DL) - F14-5 (GND) Ignition switch ON and transfer shift lever position H4 or L4 Below 1.5 V
F14-1 (DL1) - F14-5 (GND) Ignition switch ON and A.D.D. not locked Below 1.5 V
F14-1 (DL1) - F14-5 (GND) Ignition switch ON and A.D.D. locked 10 to 14 V
F14-2 (DL2) - F14-5 (GND) Ignition switch ON and A.D.D. locked Below 1.5 V
F14-2 (DL2) - F14-5 (GND) Ignition switch ON and A.D.D. not locked 10 to 14 V
F14-4 (DM1) - F14-3 (DM2) Ignition switch ON and A.D.D. not locked→ locked 10 to 14 V or 0 to 14 V pulse generation → Below 0.5 V
F14-3 (DM2) - F14-4 (DM1) Ignition switch ON and A.D.D. locked → not locked 10 to 14 V or 0 to 14 V pulse generation → Below 0.5 V
F14-5 (GND) - Body ground Always Below 1 Ω