Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TMT Made) › from 2012.10
RM1840EF _52 Drivetrain _009617 DRIVE SHAFT / PROPELLER SHAFT _0052545 PROPELLER SHAFT ASSEMBLY(for TMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TMT Made)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 2WD and Pre-Runner)

a.

Remove SST from the extension housing.


b.

Install the propeller shaft to the extension housing.


c.

Temporarily install the center support bearing with the 2 bolts. Tighten the bolts as much as possible by hand.


d.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and differential flange.


e.

Align the matchmarks on the propeller shaft flange and differential flange.


f.

Connect the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

Torque:
88 N*m (899 kgf*cm, 65 ft.*lbf)


g.
C237745
1.688,0.469 2.365,0.469 true 1.708,1.615 2.365,1.615 true 2.406,0.375 2.552,0.521 0.146,0.146 10 false *a 2.406,1.542 2.552,1.688 0.146,0.146 10 false *b 1.958,1.823 2.073,1.969 0.115,0.146 10 false A
*a Center Bearing Center Line
*b Center Bearing Housing Center Line


Unload the vehicle. The center lines of the center bearing and center bearing housing (refer to the illustration) must be adjusted so that they are within 0 +/-1 mm (0 +/-0.0394 in.) of each other. Measure the difference along the front/rear axis of the vehicle.

Distance (A):

0 +/-1 mm (0 +/-0.0394 in.)



h.

Tighten the 2 bolts of the center support bearing.

Torque:
36 N*m (369 kgf*cm, 27 ft.*lbf)


Hide 2.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

a.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and differential flange.


b.

Align the matchmarks on the propeller shaft flange and differential flange.


c.

Install the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

Torque:
88 N*m (899 kgf*cm, 65 ft.*lbf)


d.

Temporarily install the center support bearing with the 2 bolts. Tighten the bolts as much as possible by hand.


e.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and transfer flange.


f.

Align the matchmarks on the propeller shaft flange and transfer flange.


g.

Connect the propeller shaft with the 4 washers and 4 nuts.

Torque:
88 N*m (899 kgf*cm, 65 ft.*lbf)


h.
C237745
1.688,0.469 2.365,0.469 true 1.708,1.615 2.365,1.615 true 2.406,0.375 2.552,0.521 0.146,0.146 10 false *a 2.406,1.542 2.552,1.688 0.146,0.146 10 false *b 1.958,1.823 2.073,1.969 0.115,0.146 10 false A
*a Center Bearing Center Line
*b Center Bearing Housing Center Line


Unload the vehicle. The center lines of the center bearing and center bearing housing (refer to the illustration) must be adjusted so that they are within 0 +/-1 mm (0 +/-0.0394 in.) of each other. Measure the difference along the front/rear axis of the vehicle.

Distance (A):

0 +/-1 mm (0 +/-0.0394 in.)



i.

Tighten the 2 bolts of the center support bearing.

Torque:
36 N*m (369 kgf*cm, 26 ft.*lbf)