Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TMT Made) › from 2012.10
RM1840EF _52 Drivetrain _009617 DRIVE SHAFT / PROPELLER SHAFT _0052545 PROPELLER SHAFT ASSEMBLY(for TMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TMT Made)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for all universal joint spiders.


a.
C060598

Apply MP grease to a new spider and 2 new spider bearings.

NOTICE:

Be careful not to apply too much grease.



b.

Fit the spider into the yoke.


c.
C281350
1.021,0.833 1.125,0.354 1.125,0.354 1.292,0.354 false 1.344,0.271 1.688,0.458 0.344,0.188 10 false SST

Using SST, install the 2 spider bearings to the spider.

SST
09332-25010  


d.
G020755

Using SST, adjust the spider bearings so that: 1) the yoke does not overlap the snap ring grooves of the spider bearings; 2) the grooves are as wide as possible; and 3) the groove width on both sides is the same.

SST
09332-25010  


e.

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

Standard Snap Ring Thickness:
Part No. Thickness Mark
90520-T0007 2.19 mm (0.0862 in.) F
90520-T0008 2.21 mm (0.0870 in.) G
90520-T0009 2.23 mm (0.0878 in.) H
90520-T0010 2.25 mm (0.0886 in.) J
90520-T0011 2.27 mm (0.0894 in.) K
90520-T0012 2.29 mm (0.0902 in.) 1
90520-T0013 2.31 mm (0.0909 in.) 2
90520-T0014 2.33 mm (0.0917 in.) 3
90520-T0015 2.35 mm (0.0925 in.) 4
90520-T0016 2.37 mm (0.0933 in.) 5
90520-T0017 2.39 mm (0.0941 in.) 6
90520-T0018 2.41 mm (0.0949 in.) 7
90520-T0019 2.43 mm (0.0957 in.) 8
90520-T0020 2.45 mm (0.0965 in.) N
90520-T0021 2.47 mm (0.0972 in.) 10
90520-T0022 2.49 mm (0.0980 in.) A
90520-T0023 2.51 mm (0.0988 in.) B
90520-T0024 2.53 mm (0.0996 in.) C
90520-T0025 2.55 mm (0.1004 in.) D
90520-T0026 2.57 mm (0.1012 in.) E


NOTICE:
·

New snap rings must be used.

·

The snap ring thickness must be the same on both ends.




f.
C282524
2.365,0.656 1.656,0.302 1.656,0.302 1.333,0.302 true 1.115,0.198 1.427,0.354 0.313,0.156 10 false *a
*a Hammering Point


Using a plastic-faced hammer, tap the yoke until there is no clearance between the spider bearings and snap rings.


g.

Align the matchmarks on the yoke and shaft.


h.

Install new spider bearings on the shaft side.

HINT:

Use the procedure described above.



Hide 3.INSTALL CENTER NO. 1 SUPPORT BEARING ASSEMBLY

a.
C115788
0.261,0.311 0.424,0.47 0.163,0.16 10 *a
*a Front Side


Install the center support bearing to the intermediate shaft.


b.

Coat the splines of the intermediate shaft with MP grease.


c.
F049874
1.844,1.094 3.083,1.094 true 1.823,1.406 2.875,1.406 2.875,1.406 2.875,1.094 true 3.135,1.021 3.292,1.167 0.156,0.146 10 false *1
*1 Matchmark


Align the matchmarks on the flange coupling and intermediate shaft, and install the flange coupling to the intermediate shaft.


d.

Install the washer.


e.
F049875
2.333,1.104 2.552,1.583 2.552,1.583 2.635,1.583 false 2.698,1.479 3.094,1.677 0.396,0.198 10 false SST

Using SST to hold the flange coupling, press the bearing into position by installing a new lock nut.

SST
09330-00021  

Torque:
181 N*m (1850 kgf*cm, 134 ft.*lbf)


f.

Loosen the lock nut.


g.

Tighten the lock nut again.

Torque:
68 N*m (700 kgf*cm, 51 ft.*lbf)


h.
C061391

Using a chisel and hammer, stake the lock nut.


i.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and flange coupling.


j.
C281600
1.656,0.771 1.656,0.438 1.656,0.438 0.49,0.438 true 1.521,0.688 1.521,0.448 true 0.271,0.344 0.583,0.5 0.313,0.156 10 false *1
*1 Matchmark


Align the matchmarks on the flange yoke and flange coupling, and connect them with the 4 washers and 4 nuts.

Torque:
88 N*m (899 kgf*cm, 65 ft.*lbf)

NOTICE:

If any parts with matchmarks are replaced during inspection, reassemble them so that the yoke (for 2WD and Pre-Runner: sleeve yoke; for 4WD: flange yoke) of the intermediate shaft and the rear flange yoke of the propeller shaft are at right angles to each other.



Hide 4.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with MP grease.



C281603
0.865,3.865 0.865,3.313 0.865,3.313 1.365,3.313 true 3.479,3.917 3.479,3.5 3.479,3.5 3.833,3.5 true 6.167,3.917 6.167,3.292 6.167,3.292 6.5,3.292 true 3.708,4.563 3.292,4.563 3.292,4.563 3.292,3.979 true 1.51,1.094 1.51,0.542 1.51,0.542 2.01,0.542 true 4.354,1.792 3.938,1.792 3.938,1.792 3.938,1.208 true 6.292,1.135 6.292,0.51 6.292,0.51 6.625,0.51 true 0.24,0.521 0.552,0.677 0.313,0.156 10 false *A 0.24,3.177 0.552,3.333 0.313,0.156 10 false *B 2.083,0.448 2.396,0.604 0.313,0.156 10 false *1 4.417,1.698 4.729,1.854 0.313,0.156 10 false *2 6.698,0.417 7.01,0.573 0.313,0.156 10 false *3 6.563,3.198 6.875,3.354 0.313,0.156 10 false *4 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 3.563,0.25 3.875,0.406 0.313,0.156 10 false *b 3.792,4.458 4.104,4.615 0.313,0.156 10 false *2 3.906,3.406 4.219,3.563 0.313,0.156 10 false *3 3.615,3.125 3.927,3.281 0.313,0.156 10 false *b 1.073,4.75 1.385,4.906 0.313,0.156 10 false *4 1.073,4.5 1.385,4.656 0.313,0.156 10 false *1 1.073,5.01 1.385,5.167 0.313,0.156 10 false *3 1.073,5.281 1.385,5.438 0.313,0.156 10 false *2 1.104,1.771 1.417,1.927 0.313,0.156 10 false *1 1.104,2 1.417,2.156 0.313,0.156 10 false *3 1.104,2.479 1.417,2.635 0.313,0.156 10 false *2 1.427,3.219 1.74,3.375 0.313,0.156 10 false *1
*A for 2WD and Pre-Runner *B for 4WD
*1 No. 1 Grease Fitting *2 No. 2 Grease Fitting
*3 No. 3 Grease Fitting *4 No. 4 Grease Fitting
*a Spider grease fitting assembly direction for propeller shaft assembly *b Rear Side