Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made)
RM1840EF _52 Drivetrain _009617 DRIVE SHAFT / PROPELLER SHAFT _0052546 FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE UNIVERSAL JOINT SPIDER ASSEMBLY

F015023
1.823,0.979 1.823,0.26 1.823,0.26 2.438,0.26 false 1.99,1 1.99,0.26 false 2.51,0.167 2.802,0.333 0.292,0.167 10 false *1
*1 Matchmark


HINT:

Use the same procedure for both universal joint spiders.


a.

Place matchmarks on the flange yoke and propeller shaft.


b.
C061264

Using a brass bar and hammer, slightly tap in the spider bearing outer races.


c.

Using 2 screwdrivers, remove the 4 snap rings from the grooves.


d.
C282522
1.24,0.667 1.125,0.198 1.125,0.198 0.958,0.198 true 2.5,1.229 2.083,1.375 true 0.667,0.083 1.125,0.281 0.458,0.198 10 false SST 1.969,1.313 2.125,1.51 0.156,0.198 10 false A

Clamp the propeller shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Using SST, push the sleeve yoke side spider bearing until: 1) the spider almost touches the sleeve yoke or propeller shaft, and 2) the spider bearing on the opposite side is partially pushed out.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.



f.
C237736
2.167,0.677 2.677,0.677 true 2.042,1.156 2.552,1.156 false 2.729,0.573 2.979,0.76 0.25,0.188 10 false *a 2.615,1.063 2.885,1.25 0.271,0.188 10 false *1
*1 Plastic-faced Hammer
*a Hammering Point


Clamp the pushed out spider bearing outer race in a vise between aluminum plates and tap the propeller shaft to remove the spider bearing.

NOTICE:
·

Do not tap the shaft tube.

·

Do not overtighten the vise.



HINT:

Use the same procedure to remove the spider bearing from the opposite side of the spider.



g.

Separate the flange yoke and spider from the propeller shaft.


h.
F015030
2.563,1.063 2.146,1.271 true 1.01,0.771 0.75,0.146 0.75,0.146 0.656,0.146 true 0.333,0.073 0.656,0.271 0.323,0.198 10 false SST 2.021,1.219 2.177,1.417 0.156,0.198 10 false A

Reinstall the 2 removed spider bearings to the spider and clamp the spider bearings in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



i.

Using SST, push the flange yoke side spider bearing until: 1) the spider almost touches the flange yoke, and 2) the spider bearing on the opposite side is partially pushed out.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.



j.
C237737
2.521,0.521 3,0.521 true 2.563,1.031 2.979,1.031 false 3.042,0.417 3.281,0.604 0.24,0.188 10 false *a 3.031,0.948 3.281,1.125 0.25,0.177 10 false *1
*1 Plastic-faced Hammer
*a Hammering Point


Clamp the pushed out spider bearing outer race in a vise between aluminum plates and tap the flange yoke to remove the spider bearing.

NOTICE:

Do not overtighten the vise.


HINT:

Use the same procedure to remove the spider bearing from the opposite side of the spider.



k.

Separate the spider from the flange yoke.