Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made)
RM1840EF _52 Drivetrain _009617 DRIVE SHAFT / PROPELLER SHAFT _0052546 FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for both universal joint spiders.


C060598

a.

Apply MP grease to a new spider and 2 new spider bearings.

NOTICE:

Be careful not to apply too much grease.



b.

Fit the spider into the flange yoke.


c.
C281350
1.021,0.833 1.125,0.354 1.125,0.354 1.292,0.354 false 1.344,0.271 1.688,0.458 0.344,0.188 10 false SST

Using SST, install the 2 spider bearings to the spider.

SST
09332-25010  


d.
G020755

Using SST, adjust the spider bearings so that: 1) the flange yoke does not overlap the snap ring grooves of the spider bearings; 2) the grooves are as wide as possible; and 3) the groove width on both sides is the same.

SST
09332-25010  


e.

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

Standard Snap Ring Thickness :
Part No. Thickness Mark
90520-T0007 2.19 mm (0.0862 in.) F
90520-T0008 2.21 mm (0.0870 in.) G
90520-T0009 2.23 mm (0.0878 in.) H
90520-T0010 2.25 mm (0.0886 in.) J
90520-T0011 2.27 mm (0.0894 in.) K
90520-T0012 2.29 mm (0.0902 in.) 1
90520-T0013 2.31 mm (0.0909 in.) 2
90520-T0014 2.33 mm (0.0917 in.) 3
90520-T0015 2.35 mm (0.0925 in.) 4
90520-T0016 2.37 mm (0.0933 in.) 5
90520-T0017 2.39 mm (0.0941 in.) 6
90520-T0018 2.41 mm (0.0949 in.) 7
90520-T0019 2.43 mm (0.0957 in.) 8
90520-T0020 2.45 mm (0.0965 in.) N
90520-T0021 2.47 mm (0.0972 in.) 10
90520-T0022 2.49 mm (0.0980 in.) A
90520-T0023 2.51 mm (0.0988 in.) B
90520-T0024 2.53 mm (0.0996 in.) C
90520-T0025 2.55 mm (0.1004 in.) D
90520-T0026 2.57 mm (0.1012 in.) E


NOTICE:
·

New snap rings must be used.

·

The snap ring thickness must be the same on both ends.




f.
G102178
1.479,0.313 2.344,0.677 false 1.271,0.208 1.583,0.406 0.313,0.198 10 false *a
*a Hammering Point


Using a plastic-faced hammer, tap the flange yoke until there is no clearance between the spider bearings and snap rings.


g.

Align the matchmarks on the flange yoke and propeller shaft.


h.

Install new spider bearings on the sleeve yoke side.

HINT:

Use the procedure described above.



Hide 3.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with MP grease.



C281379
1.031,1.458 0.76,1.458 0.76,1.458 0.76,0.99 true 4.646,0.896 4.646,0.333 4.646,0.333 4.896,0.333 true 5.052,1.49 4.854,1.49 4.854,1.49 4.854,0.99 true 5.708,1.167 6.021,1.323 0.313,0.156 10 false *1 5.708,0.875 6.021,1.031 0.313,0.156 10 false *2 5.708,0.604 6.021,0.76 0.313,0.156 10 false *3 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 3.063,0.198 3.375,0.354 0.313,0.156 10 false *b 1.104,1.365 1.417,1.521 0.313,0.156 10 false *1 4.958,0.25 5.271,0.406 0.313,0.156 10 false *2 5.104,1.396 5.417,1.552 0.313,0.156 10 false *3
*1 No. 1 Grease Fitting *2 No. 2 Grease Fitting
*3 No. 3 Grease Fitting - -
*a Spider grease fitting assembly direction for front propeller shaft assembly *b Rear Side