Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TSAM Made) › from 2012.04
RM1840EF _52 Drivetrain _009617 DRIVE SHAFT / PROPELLER SHAFT _0052551 PROPELLER SHAFT ASSEMBLY(for TSAM Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TSAM Made)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE REAR SLIDING SHAFT BOOT

a.

Place matchmarks on the propeller shaft and sleeve yoke.


b.

Using a side cutter or pliers, remove the small and large boot clamps.


c.

Disconnect the boot from the sleeve yoke.


d.

Remove the sleeve yoke, and then remove the boot from the propeller shaft.


Hide 2.REMOVE UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for all universal joint spiders.


a.
F052432
1.604,0.802 1.604,0.375 1.604,0.375 2.146,0.375 false 1.823,0.865 1.823,0.375 false 2.229,0.281 2.521,0.458 0.292,0.177 10 false *1
*1 Matchmark


Place matchmarks on the yokes.


b.
C118615
1.75,0.979 1.75,0.333 1.75,0.333 2.229,0.333 true 2,0.844 2,0.333 true 2.302,0.25 2.583,0.427 0.281,0.177 10 false *1
*1 Matchmark


Place matchmarks on the center yoke and the part it is connected to (yoke or shaft).


c.
F052433

Using a brass bar and hammer, slightly tap in the spider bearing outer races.


d.

Using needle nose pliers, remove the 4 snap rings from the grooves.


e.
C282522
1.24,0.667 1.125,0.198 1.125,0.198 0.958,0.198 true 2.5,1.229 2.083,1.375 true 0.667,0.083 1.125,0.281 0.458,0.198 10 false SST 1.969,1.313 2.125,1.51 0.156,0.198 10 false A

Clamp the propeller shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



f.

Using SST, push the sleeve yoke side spider bearing until: 1) the spider almost touches the sleeve yoke or propeller shaft, and 2) the spider bearing on the opposite side is partially pushed out.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.



g.
C237736
2.167,0.677 2.677,0.677 true 2.042,1.156 2.552,1.156 false 2.729,0.573 2.979,0.76 0.25,0.188 10 false *a 2.615,1.063 2.865,1.24 0.25,0.177 10 false *1
*1 Plastic-faced Hammer
*a Hammering Point


Clamp the pushed out spider bearing outer race in a vise between aluminum plates and tap the propeller shaft to remove the spider bearing.

NOTICE:
·

Do not tap the shaft tube.

·

Do not overtighten the vise.



NOTICE:

Do not tap the shaft tube.


HINT:

Use the same procedure to remove the spider bearing from the opposite side of the spider.



h.

Remove the flange yoke and spider from the propeller shaft.


i.
F015030
2.563,1.063 2.146,1.271 true 1.01,0.771 0.75,0.146 0.75,0.146 0.656,0.146 true 0.333,0.073 0.656,0.271 0.323,0.198 10 false SST 2.021,1.219 2.177,1.417 0.156,0.198 10 false A

Reinstall the 2 removed spider bearings to the spider and clamp the spider bearings in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



j.

Using SST, push the flange yoke side spider bearing until: 1) the spider almost touches the flange yoke, and 2) the spider bearing on the opposite side is partially pushed out.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.



k.
C237737
2.521,0.521 3,0.521 true 2.563,1.031 2.979,1.031 false 3.042,0.417 3.24,0.594 0.198,0.177 10 false *a 3.031,0.938 3.25,1.115 0.219,0.177 10 false *1
*1 Plastic-faced Hammer
*a Hammering Point


Clamp the pushed out spider bearing outer race in a vise between aluminum plates and tap the flange yoke to remove the spider bearing.

NOTICE:

Do not overtighten the vise.


HINT:

Use the same procedure to remove the spider bearing from the opposite side of the spider.



l.

Separate the spider from the flange yoke.


Hide 3.REMOVE CENTER NO. 1 SUPPORT BEARING ASSEMBLY

C118616

a.

Clamp the center yoke in a vise between aluminum plates.


b.

Using a hammer and chisel, loosen the staked part of the nut and remove the nut and washer.


c.
C118617
1.74,1.115 1.74,0.521 1.74,0.521 2.698,0.521 true 1.76,1.25 2.115,1.25 2.115,1.25 2.115,0.521 true 2.76,0.448 3.01,0.625 0.25,0.177 10 false *1
*1 Matchmark


Place matchmarks on the intermediate shaft and center yoke.


d.

Using a brass bar and hammer, tap out the center yoke.


e.

Remove the washer and center support bearing from the intermediate shaft.